Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0328431 MULTI-TERRAIN MONITOR SYSTEM C

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the parking assist ECU receives a signal via CAN communication from the steering sensor that indicates a power supply system problem.

DTC Code DTC Detection Condition Trouble Area
C1625 Open or short in steering angle sensor +B
·

Harness or connector

·

Steering sensor



WIRING DIAGRAM

E376977E06
0.74,0.635 2.042,0.823 1.302,0.188 10 false from IG NO.1 Relay 1.146,1.271 1.99,1.667 0.844,0.396 10 false from Battery 2.385,0.792 3.438,1.042 1.052,0.25 10 false ECU-IG NO.1 2.531,1.469 3.375,1.635 0.844,0.167 10 false ECU-B 4.156,0.635 4.354,0.802 0.198,0.167 10 false IG 4.156,1.271 4.458,1.438 0.302,0.167 10 false BAT 4.167,1.969 4.635,2.271 0.469,0.302 10 false ESS 3.938,0.5 4.094,0.667 0.156,0.167 10 false 4 3.938,1.156 4.083,1.323 0.146,0.167 10 false 5 3.927,1.854 4.063,2.021 0.135,0.167 10 false 1 0.76,3.323 2.469,3.656 1.708,0.333 10 false : CAN Communication Line 4.063,2.406 4.552,2.563 0.49,0.156 10 false G205 4.073,2.594 5.146,2.948 1.073,0.354 10 false Steering Sensor 5.719,2.448 7.042,2.802 1.323,0.354 10 false Parking Assist ECU

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

(See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags.

Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING SENSOR - BATTERY AND BODY GROUND)
a.
E376978C03
1.469,0.229 1.938,0.458 0.469,0.229 1.917,1.229 2.417,0.865 2.417,0.865 2.604,0.865 true 2.104,1.375 2.375,1.74 2.375,1.74 2.531,1.74 true 1.271,1.24 0.948,0.99 0.948,0.99 0.781,0.99 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.458,0.917 0.802,1.083 0.344,0.167 10 false ESS 2.604,1.656 2.948,1.823 0.344,0.167 10 false BAT 2.656,0.792 2.927,0.938 0.271,0.146 10 false IG 1.542,0.271 1.938,0.438 0.396,0.167 10 false G205
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G205-1 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G205-4 (IG) - G205-1 (ESS) Engine switch on (IG) 11 to 14 V
G205-5 (BAT) - G205-1 (ESS) Always 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR