Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › 2020.08–2021.06
RM27T0E _56 Audio / Visual / Telematics _056796 TELEMATICS _0277431 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1573  Short in Telephone Antenna Circuit  B15CB  Telephone Antenna Disconnected  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1573 Short in Telephone Antenna Circuit Telephone antenna assembly impedance (Ω) is lower than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Short circuit)
·

Telematics transceiver

·

Telephone antenna assembly

·

No. 2 antenna cord sub-assembly

·

Telephone antenna cord sub-assembly

·

Harness or connector


B15CB Telephone Antenna Disconnected Telephone antenna assembly impedance (Ω) is higher than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Open circuit)
·

Telematics transceiver

·

Telephone antenna assembly

·

No. 2 antenna cord sub-assembly

·

Telephone antenna cord sub-assembly

·

Harness or connector



WIRING DIAGRAM

E350969E05
5.708,2.333 6.219,2.521 0.51,0.188 10 false H101 5.708,2.531 7.156,2.781 1.448,0.25 10 false Telematics Transceiver 0.208,2.302 1.396,2.708 1.188,0.406 10 false Telephone Antenna Assembly 1.552,2.448 3.094,2.844 1.542,0.396 10 false Telephone Antenna Cord Sub-assembly 3.583,2.469 4.844,2.844 1.26,0.375 10 false No. 2 Antenna Cord Sub-assembly 4.323,1.24 4.625,1.448 0.302,0.208 10 false D-3 4.271,1.75 4.635,2.01 0.365,0.26 10 false D-3a 3.542,1.24 3.844,1.448 0.302,0.208 10 false C-3 3.552,1.74 3.917,1.948 0.365,0.208 10 false C-3a 2.573,1.24 2.875,1.448 0.302,0.208 10 false B-3 2.51,1.74 2.865,1.948 0.354,0.208 10 false B-3a 1.385,1.24 1.688,1.448 0.302,0.208 10 false A-4 1.385,1.74 1.74,1.958 0.354,0.219 10 false A-4a 5.167,1.146 5.323,1.344 0.156,0.198 10 false 3 5.688,1.25 5.844,1.448 0.156,0.198 10 false 1 5.083,1.354 5.396,1.552 0.313,0.198 10 false H81 4.656,1.354 5.021,1.563 0.365,0.208 10 false TEL1 5.885,1.354 6.25,1.563 0.365,0.208 10 false TEL1

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TELEPHONE ANTENNA ASSEMBLY
2.INSPECT TELEPHONE ANTENNA ASSEMBLY
a.

Remove the telephone antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.
E271865C15
1.979,1.448 2.229,1.417 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.271,1.333 2.583,1.531 0.313,0.198 10 false 4a
*a Telephone Antenna Assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA ASSEMBLY

3.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the telephone antenna assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.
E350951C14
1.646,0.271 2.042,0.552 0.396,0.281 1.677,2.563 2.073,2.844 0.396,0.281 1.271,1.563 1.688,1.521 true 2.01,3.99 2.542,4.156 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.073,1.479 1.385,1.677 0.313,0.198 10 false 4a 2.594,4.094 2.906,4.292 0.313,0.198 10 false 3a 1.792,0.333 1.948,0.531 0.156,0.198 10 false A 1.823,2.625 1.979,2.823 0.156,0.198 10 false B 0.156,2.594 0.469,2.792 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Telephone Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - B-3 Always Below 1 Ω
A-4a - B-3a Always Below 1 Ω
A-4 or B-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA CORD SUB-ASSEMBLY

4.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the telephone antenna cord sub-assembly.


b.

Disconnect the antenna connector from the wire harness.


c.
E350952C08
1.583,0.396 2.021,0.677 0.438,0.281 1.625,2.615 2.063,2.896 0.438,0.281 1.979,1.833 2.531,1.833 true 2.01,4 2.531,3.896 true 1.25,4.417 1.427,4.417 1.427,4.417 1.823,3.969 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.75,0.458 1.906,0.656 0.156,0.198 10 false C 1.813,2.677 1.969,2.875 0.156,0.198 10 false D 2.583,1.76 2.781,1.958 0.198,0.198 10 false 3a 2.573,3.813 2.771,4.01 0.198,0.198 10 false 3a 0.885,4.333 1.333,4.563 0.448,0.229 10 false TEL1 0.188,2.583 0.5,2.781 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Telephone Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Wire Harness)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-3 - D-3 (TEL1) Always Below 1 Ω
C-3a - D-3a Always Below 1 Ω
C-3 or D-3 (TEL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER [DATA COMMUNICATION MODULE (DCM)])

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER [DATA COMMUNICATION MODULE (DCM)])
a.

Disconnect the H81 No. 2 antenna cord sub-assembly connector from the instrument panel wire.


b.

Disconnect the H101 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H81-3 (TEL1) - H101-1 (TEL1) Always Below 1 Ω
H81-3 (TEL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT