These DTCs are stored when a malfunction occurs in the telephone antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C0 | Short in GPS Antenna | Current to the telephone antenna assembly is lower than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Short circuit) |
·
Telematics transceiver ·
Telephone antenna assembly ·
Antenna divider (w/ Heated Windshield Defroster System) ·
No. 2 antenna cord sub-assembly ·
Telephone antenna cord sub-assembly |
| B15C1 | Open in GPS Antenna | Current for telephone antenna assembly is higher than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Open circuit) |
·
Telematics transceiver ·
Telephone antenna assembly ·
Antenna divider (w/ Heated Windshield Defroster System) ·
No. 2 antenna cord sub-assembly ·
Telephone antenna cord sub-assembly |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the antenna connector from the telephone antenna assembly.
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
| *a | Front view of wire harness connector
(to Telephone Antenna Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 - B-2 | Always | Below 1 Ω |
| A-2a - B-2a | Always | Below 1 Ω |
| A-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Telephone Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Wire Harness) |
Disconnect the antenna connector from the telephone antenna cord sub-assembly.
Disconnect the antenna connector from the wire harness.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-2 - H81-2 (GPS1) | Always | Below 1 Ω |
| B-2a - H81-2a | Always | Below 1 Ω |
| B-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle condition.
| Result | Proceed to |
|---|---|
| w/o Heated Windshield Defroster System | A |
| w/ Heated Windshield Defroster System | B |
A
B
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to telematics transceiver) |
Disconnect the H81 No. 2 antenna cord sub-assembly connector from the instrument panel wire.
Disconnect the H102 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H81-2 (GPS1) - H102-1 (GPS1) | Always | Below 1 Ω |
| H81-2a - H102-1a | Always | Below 1 Ω |
| H81-2 (GPS1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Divider) |
Disconnect the H81 No. 2 antenna cord sub-assembly connector from the wire harness.
Disconnect the C Antenna Divider connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H81-2 (GPS1) - C-6 | Always | Below 1 Ω |
| H81-2a - C-6a | Always | Below 1 Ω |
| H81-2 (GPS1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
| *a | Component without harness connected
(Antenna Divider) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 6 | Always | 10 kΩ or higher |
| 5 - 6 | Always | Below 1 Ω |
| 5 - 5a | Always | 10 kΩ or higher |
| 6 - 6a | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Antenna Divider) |
| *b | Front view of wire harness connector
(to Telematics Transceiver) |
Disconnect the C Antenna Divider connector.
Disconnect the H102 telematics transceiver connector from the wire harness.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-5 - H102-1 (GPS1) | Always | Below 1 Ω |
| C-5a - H102-1a | Always | Below 1 Ω |
| C-5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG