Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (except i-ART) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0438250 CRUISE CONTROL SYSTEM(except i-ART) J

CRUISE CONTROL  CRUISE CONTROL SYSTEM(except i-ART)  Clutch Switch Circuit  


DESCRIPTION

While depressing the clutch pedal, the clutch switch sends a signal to terminal D of the ECM. The ECM cancels cruise control when terminal D receives the signal.

WIRING DIAGRAM

C439933E08
1.563,0.052 3.344,0.26 1.781,0.208 10 false from IG NO.1 Relay 2.875,1 3.042,1.167 0.167,0.167 10 false 1 4.021,1 4.24,1.229 0.219,0.229 10 false 2 2.708,1.594 4.51,1.823 1.802,0.229 10 false Clutch Switch Assembly 2.708,1.417 3.042,1.583 0.333,0.167 10 false A43 1.563,1.292 2.167,1.49 0.604,0.198 10 false IG1 5.802,1 6.104,1.208 0.302,0.208 10 false 27 6.104,1.135 6.521,1.302 0.417,0.167 10 false D 6.333,2.531 6.833,2.844 0.5,0.313 10 false ECM 6.344,2.354 6.688,2.573 0.344,0.219 10 false C34

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the ECM refer to Service Bulletin.



PROCEDURE

1.INSPECT CLUTCH SWITCH ASSEMBLY
a.

Remove the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)

NG

REPLACE CLUTCH SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)
a.
C326224C24
1.448,0.198 1.906,0.5 0.458,0.302 1.563,0.25 1.969,0.448 0.406,0.198 10 false A43 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Clutch Switch Assembly)


Disconnect the clutch switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A43-1 - Body ground Ignition Switch ON 11 to 14 V
A43-1 - Body ground Ignition Switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM)
a.

Disconnect the A43 clutch switch assembly connector.


b.

Disconnect the C34 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-2 - C34-27 (D) Always Below 1 Ω
A43-2 or C34-27 (D) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR