Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for i-ART) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0438249 CRUISE CONTROL SYSTEM(for i-ART) J

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for i-ART)  Clutch Switch Circuit  


DESCRIPTION

While depressing the clutch pedal, the clutch switch sends a signal to terminal D of the ECM. The ECM cancels cruise control when terminal D receives the signal.

WIRING DIAGRAM

C439933E09
1.563,0.052 3.344,0.26 1.781,0.208 10 false from IG NO.1 Relay 2.875,1 3.042,1.167 0.167,0.167 10 false 1 4.021,1 4.24,1.229 0.219,0.229 10 false 2 2.708,1.729 4.51,1.958 1.802,0.229 10 false Clutch Switch Assembly 2.708,1.552 3.74,1.813 1.031,0.26 10 false A43*1, r3*2 1.563,1.292 2.167,1.49 0.604,0.198 10 false IG1 5.802,1 6.104,1.208 0.302,0.208 10 false 14 6.104,1.135 6.521,1.302 0.417,0.167 10 false D 6.333,2.531 6.833,2.844 0.5,0.313 10 false ECM 6.323,2.354 6.844,2.594 0.521,0.24 10 false C149 0.219,3.031 2.313,3.271 2.094,0.24 10 false *1: for LHD 0.219,3.354 2.313,3.594 2.094,0.24 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the ECM refer to Service Bulletin.



PROCEDURE

1.INSPECT CLUTCH SWITCH ASSEMBLY
a.

Remove the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)

NG

REPLACE CLUTCH SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)
a.
C326224C25
1.052,0.198 1.51,0.5 0.458,0.302 1.854,0.198 2.313,0.5 0.458,0.302 1.177,0.26 1.583,0.458 0.406,0.198 10 false A43 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 2.021,0.26 2.427,0.458 0.406,0.198 10 false r3 1.563,0.271 1.875,0.469 0.313,0.198 10 false *A 2.354,0.271 2.667,0.469 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Clutch Switch Assembly)


Disconnect the clutch switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A43-1 - Body ground Ignition Switch ON 11 to 14 V
A43-1 - Body ground Ignition Switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
r3-1 - Body ground Ignition Switch ON 11 to 14 V
r3-1 - Body ground Ignition Switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM)
a.

Disconnect the A43*1 or r3*2 clutch switch assembly connector.

*1: for LHD

*2: for RHD


b.

Disconnect the C149 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A43-2 - C149-14 (D) Always Below 1 Ω
A43-2 or C149-14 (D) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
r3-2 - C149-14 (D) Always Below 1 Ω
r3-2 or C149-14 (D) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR