Home › Brake › BRAKE SYSTEM (OTHER) › HYDRAULIC BRAKE BOOSTER(for LHD) › from 2020.08
RM27T0E _54 Brake _053713 BRAKE SYSTEM (OTHER) _0260930 HYDRAULIC BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  HYDRAULIC BRAKE BOOSTER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When installing, coat the parts indicated by arrows with lithium soap base glycol grease (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER(for LHD)>COMPONENTS).

·

Be sure not to allow the pump to contact the floor; support it with the booster body. If the pump contacts the floor, the red brake tube between the pump and booster body may be deformed, the operating sound of the pump may become loud enough to hear within the cabin, and fluid may leak.

·

As high pressure is applied to the brake actuator tube No. 1, never deform it.

·

Do not turn the ignition switch to ON until the procedures are completed.

·

Before starting the work, make sure that the ignition switch is off and depress the brake pedal more than 20 times.



HINT:

When pressure in the power supply system is released, the reaction force decreases and the stroke becomes longer.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Hide 3.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes into contact with a painted surface.


Hide 73900 4.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

a.

Remove the lower No. 1 instrument panel airbag assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>KNEE AIRBAG ASSEMBLY>REMOVAL).


Hide 6.REMOVE HYDRAULIC BRAKE BOOSTER ASSEMBLY

a.
C215277

Disconnect the 3 connectors from the hydraulic brake booster assembly.


b.
F051200E16
1.198,1.167 1.198,0.74 1.198,0.74 0.698,0.74 true 1.594,1.51 1.594,0.094 1.594,0.094 1.281,0.094 true 2.042,1.719 2.365,0.146 2.365,0.146 2.479,0.146 true 2.479,1.813 2.75,0.76 2.75,0.76 2.906,0.76 true 0.49,0.667 0.667,0.833 0.177,0.167 10 true *3 1.073,0.021 1.229,0.188 0.156,0.167 10 true *1 2.531,0.073 2.729,0.219 0.198,0.146 10 true *2 2.948,0.688 3.146,0.833 0.198,0.146 10 true *4

Use tags or make a memo to identify the place to reconnect.

HINT:
·

*1: To front wheel cylinder RH

·

*2: To front wheel cylinder LH

·

*3: To rear wheel cylinder RH

·

*4: To rear wheel cylinder LH




c.
C217148

Using a union nut wrench, disconnect the 4 brake lines from the hydraulic brake booster assembly.


d.
C214646

Remove the 4 nuts and pull out the hydraulic brake booster assembly.


Hide 44785 7.REMOVE BRAKE BOOSTER GASKET

a.

Remove the brake booster gasket from the hydraulic brake booster assembly.