Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › from 2020.08
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261258 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 53292A 3.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 53828J 4.REMOVE FRONT FENDER SIDE PANEL PROTECTOR LH

a.
E199696

Detach the 3 clips and guide and remove the front fender side panel protector LH.


Hide 53827K 5.REMOVE FRONT FENDER SIDE PANEL PROTECTOR RH

HINT:

Use the same procedure for the LH side.


Hide 53867H 6.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

a.
B487048

Detach the 3 claws and guide and remove the front fender to cowl side seal LH.


Hide 53866J 7.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure for the LH side.


Hide 85192 8.REMOVE WINDSHIELD WIPER ARM COVER

a.
E198979C03
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver, detach the 3 claws and remove the windshield wiper arm cover.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the RH side and LH side.




Hide 9.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E197606

Remove the nut and front wiper arm and blade assembly LH.


Hide 10.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
E197608

Remove the nut and front wiper arm and blade assembly RH.


Hide 53383 11.REMOVE HOOD TO COWL TOP SEAL

a.
E197610

Detach the 7 claws and 2 clips and remove the hood to cowl top seal.


Hide 55784B 12.REMOVE CENTER NO. 2 COWL TOP VENTILATOR LOUVER

a.
E197612

Detach the 2 claws and 3 guides and remove the center No. 2 cowl top ventilator louver.


Hide 55781E 13.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.
E197614C02
1.021,1.51 1.333,1.708 0.313,0.198 10 false *a 2.125,0.24 2.438,0.438 0.313,0.198 10 false *b
*a Guide (A)
*b Guide (B)


Remove the 2 clips.


b.

Detach the 6 claws and guide (A).


c.

Detach the 10 guides (B) and pull out the cowl top ventilator louver sub-assembly.


Hide 14.REMOVE WINDSHIELD WIPER MOTOR AND LINK

a.
E197616

Detach the clamp and disconnect the connector.


b.
E197618

Remove the 2 bolts.


c.
E197620C01
1.51,0.865 1.719,1.052 true 1.354,0.76 1.667,0.958 0.313,0.198 10 false *1
*1 Grommet


Detach the grommet and remove the windshield wiper motor and link as shown in the illustration.

NOTICE:

Be careful not to damage the windshield when removing the windshield wiper motor and link.



Hide 85012A 15.REMOVE FRONT WIPER CRANK SUB-ASSEMBLY (for RHD, w/ Spring)

a.
E201892C01
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver, disconnect the windshield wiper link rod from the crank arm pivot of the front wiper crank sub-assembly as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



b.
E201895

Remove the nut and front wiper crank sub-assembly.


Hide 85110 16.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

a.

w/o Spring:

i.
E197622C03
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver, disconnect the windshield wiper link rod from the crank arm pivot of the front wiper crank as shown in the illustration.

HINT:

Tape the screwdriver tip before use.




b.
E197625

Disconnect the connector.


c.

Using a T30 ''TORX'' socket wrench, remove the 2 bolts and windshield wiper motor assembly.


Hide 82375B 17.REMOVE WIPER MOTOR WIRE

a.
E197627

Detach the claw and remove the wiper motor wire.