Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for LED Headlight) › from 2020.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0326212 LIGHTING SYSTEM(for LED Headlight) J

LIGHTING (EXT)  LIGHTING SYSTEM(for LED Headlight)  Front Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the front fog light.

WIRING DIAGRAM

w/o Stop and Start System:
E374186E02
5.396,4.104 7.083,4.542 1.688,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 3.688,4.104 5.313,4.458 1.625,0.354 10 false Driver Side Junction Block Assembly 6.135,1.615 6.698,1.875 0.563,0.26 10 false FFGO 5.813,1.615 6.375,1.875 0.563,0.26 10 false A 4.729,1.917 5.292,2.177 0.563,0.26 10 false FOG FR 2.729,1.51 3.292,1.771 0.563,0.26 10 false FOG FR 1.125,1.292 2.094,1.583 0.969,0.292 10 false from Battery 0.99,4.104 2.729,4.385 1.74,0.281 10 false B6 0.969,2.708 2.708,2.99 1.74,0.281 10 false B5 0.969,2.865 2.708,3.146 1.74,0.281 10 false Fog Light Assembly LH 1,4.26 2.74,4.542 1.74,0.281 10 false Fog Light Assembly RH 2.25,2.042 3.99,2.323 1.74,0.281 10 false B 2.24,3.396 3.979,3.677 1.74,0.281 10 false B 1.031,3.406 2.771,3.688 1.74,0.281 10 false E 1.031,2.042 2.771,2.323 1.74,0.281 10 false E 2.479,2.042 4.219,2.323 1.74,0.281 10 false 2 2.479,3.406 4.219,3.688 1.74,0.281 10 false 2 0.833,3.396 2.573,3.677 1.74,0.281 10 false 1 0.844,2.031 2.583,2.313 1.74,0.281 10 false 1 3.656,2.135 4.042,2.385 0.385,0.25 10 false 2M 3.656,1.344 4.042,1.594 0.385,0.25 10 false 2M 3.667,1.146 4.052,1.396 0.385,0.25 10 false 18 3.667,1.958 4.052,2.208 0.385,0.25 10 false 19 5.823,1.448 6.385,1.708 0.563,0.26 10 false 7

w/ Stop and Start System:
E374186E07
5.396,4.104 7.083,4.542 1.688,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 3.688,4.104 5.313,4.458 1.625,0.354 10 false Driver Side Junction Block Assembly 6.135,1.615 6.698,1.875 0.563,0.26 10 false FFGO 5.813,1.615 6.375,1.875 0.563,0.26 10 false A 4.729,1.917 5.292,2.177 0.563,0.26 10 false FOG FR 2.729,1.51 3.292,1.771 0.563,0.26 10 false FOG FR 0.823,1.188 1.948,1.542 1.125,0.354 10 false from Engine Stop and Start ECU 0.99,4.104 2.729,4.385 1.74,0.281 10 false B6 0.969,2.708 2.708,2.99 1.74,0.281 10 false B5 0.969,2.865 2.708,3.146 1.74,0.281 10 false Fog Light Assembly LH 1,4.26 2.74,4.542 1.74,0.281 10 false Fog Light Assembly RH 2.25,2.042 3.99,2.323 1.74,0.281 10 false B 2.24,3.396 3.979,3.677 1.74,0.281 10 false B 1.031,3.406 2.771,3.688 1.74,0.281 10 false E 1.031,2.042 2.771,2.323 1.74,0.281 10 false E 2.479,2.042 4.219,2.323 1.74,0.281 10 false 2 2.479,3.406 4.219,3.688 1.74,0.281 10 false 2 0.833,3.396 2.573,3.677 1.74,0.281 10 false 1 0.844,2.031 2.583,2.313 1.74,0.281 10 false 1 3.656,2.135 4.042,2.385 0.385,0.25 10 false 2M 3.656,1.344 4.042,1.594 0.385,0.25 10 false 2M 3.667,1.146 4.052,1.396 0.385,0.25 10 false 18 3.667,1.958 4.052,2.208 0.385,0.25 10 false 19 5.823,1.448 6.385,1.708 0.563,0.26 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuse for circuits related to this system before performing the follow procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, perform the Active Test.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DATA LIST / ACTIVE TEST

Main Body
Tester Display Measurement Item Control Range Diagnostic Note
Front Fog Light Relay Front fog lights OFF or ON -

OK:

Front fog light relay operates (front fog lights turn on).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - FOG LIGHT ASSEMBLY AND BATTERY)
2.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - FOG LIGHT ASSEMBLY AND BATTERY)
a.

Disconnect the 2M driver side junction block assembly connector.


b.

Disconnect the B5 fog light assembly LH connector.


c.

Disconnect the B6 fog light assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

2M-18 - Body ground Always 11 to 14 V*1
10.5 to 16 V*2



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2M-19 - B5-2 (B) Always Below 1 Ω
2M-19 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.
E377373C02
1.385,0.292 1.865,0.49 0.479,0.198 1.479,2.083 1.958,2.281 0.479,0.198 1.281,3.073 1.094,3.073 1.094,3.073 0.865,2.74 true 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.521,0.302 1.833,0.458 0.313,0.156 10 false 2M 1.656,2.094 1.969,2.25 0.313,0.156 10 false A 1.323,2.938 1.823,3.198 0.5,0.26 10 false FFGO
*a Component without harness connected
(Driver Side Junction Block Assembly)


Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2M-19 - Battery negative (-) terminal Battery not connected to 2M-18 and A-7 (FFGO) Below 1 V
Battery positive (+) → 2M-18
Battery negative (-) → A-7 (FFGO)
11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY