Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side) › from 2021.06
RM27T0E _58 Vehicle Interior _053737 SEAT _0261118 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type LH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 72173B 1.INSTALL REAR SEAT TRACK ADJUSTING HANDLE LH

B237696

a.

Install the rear seat track adjusting handle LH.

HINT:

Make sure the handle is straight when installing it, and check that it is centered.



Hide 71016A 2.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

a.

Install the rear seat cushion frame sub-assembly LH with the 6 nuts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 72728 3.INSTALL REAR SEAT INNER RECLINING PROTECTOR RH

a.
B452608

Attach the guide and claw to install the rear seat inner reclining protector RH.


Hide 71018 4.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH

B237693C02
0.344,1.521 0.635,1.521 0.635,1.521 0.938,1.125 true 0.198,1.406 0.354,1.604 0.156,0.198 10 false *a
*a Outer Belt Installation Bolt


a.

Temporarily install the rear seatback frame sub-assembly LH with the 2 bolts and 2 "TORX" bolts.


b.

Install the bolt to the bolt hole for the outer belt.


c.

Using a T45 "TORX" socket wrench, tighten the 2 "TORX" bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


d.

Tighten the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Remove the bolt from the bolt hole for the outer belt.


Hide 82194 5.INSTALL REAR SEAT WIRE LH (w/ Seat Wire Harness)

a.

Attach the clamp to install the rear seat wire LH to the rear seat cushion frame sub-assembly LH.


b.

Attach the claw to connect the rear seat wire connector to the rear seat upper track rail sub-assembly LH.


Hide 87501D 6.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

Hide 72068 7.INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH

a.

Install the rear back lock control lever sub-assembly LH with the 2 nuts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 72704B 8.INSTALL REAR NO. 2 SEAT RECLINING CONTROL CABLE

a.

Install the rear No. 2 seat reclining control cable to the seat frame.


b.

Attach the 3 cable clamps and connect the cable.


Hide 72704A 9.INSTALL REAR SEAT RECLINING CONTROL CABLE

a.

Install the rear seat reclining control cable to the seat frame.


b.

Attach the 3 cable clamps and connect the rear seat reclining control cable.


c.

Install 4 new cable ties.


Hide 73187A 11.INSTALL REAR SEAT SHOULDER BELT GUIDE

a.

Attach the guide and claw to install the rear seat shoulder belt guide.


Hide 71499C 12.INSTALL REAR SEAT CUSHION SPRING DAMPER

a.

Install the rear seat cushion spring damper with the 2 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 71879B 13.INSTALL REAR SEAT RECLINING COVER INNER LH

a.

Attach the guide and claw to install the rear seat reclining cover inner LH.


Hide 73949 14.INSTALL CAP

a.

Attach the 2 claws to install the cap.


Hide 71828B 15.INSTALL REAR SEAT REAR CUSHION MOULDING LH

B237682

a.

Move the rear seat rear cushion moulding LH in the direction of the arrow to attach the guide.


b.

Attach the 4 claws and clip to install the rear seat rear cushion moulding LH.


Hide 71876J 16.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.

Attach the 2 claws to install the reclining adjuster inside cover LH.


b.

Install the 2 screws.


Hide 71879A 17.INSTALL REAR SEAT INNER RECLINING COVER LH

a.

Attach the guide and install the rear seat inner reclining cover LH with the 2 screws.


Hide 71697 18.INSTALL REAR SEATBACK EDGE PROTECTOR

a.

Install the rear seatback edge protector to the rear seatback frame sub-assembly LH.


Hide 87510Q 19.INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71078S 20.INSTALL SEPARATE TYPE REAR SEATBACK COVER

a.

Set the separate type rear seatback cover in place.


b.
B237678C03
2.115,2.594 1.948,2.594 1.948,2.594 1.615,3.781 false 2.135,2.521 2.365,2.719 0.229,0.198 10 false *a
*a Hog Ring Pliers


Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 8 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




c.
B248336

w/ Seat Heater System:

i.

Connect the rear seatback heater assembly wire harness to the separate type rear seatback pad.



Hide 21.INSTALL SEATBACK COVER WITH PAD

a.

w/ Seat Heater System:

i.
B360132C01
2.146,1.438 2.302,1.646 true 2.26,1.656 2.448,1.823 0.188,0.167 10 false *a
*a Paint Mark


Install the wire harness as shown in the illustration.



b.
B237675

Connect the outer belt to the seatback cover with pad.


c.

Attach the hooks.

B449828C01
1.854,1.677 2.125,0.677 2.125,0.677 2.271,0.677 false 4.125,1.417 4.844,1.417 true 4.021,0.208 4.823,0.208 true 4.125,0.375 4.708,0.208 true 4.594,0.75 4.698,0.208 true 2.281,0.594 2.594,0.792 0.313,0.198 10 false *a 4.844,0.125 5.156,0.323 0.313,0.198 10 false *c 3.969,1.323 4.281,1.521 0.313,0.198 10 false *b
*a Hog Ring Pliers *b Hook
*c Hog Ring - -



d.

Using hog ring pliers, install the seatback cover with pad with 10 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.




Hide 71931B 22.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

a.

Attach the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.


Hide 71890A 23.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH

a.

Attach the 7 clips to install the rear seatback board carpet assembly LH.


Hide 72996A 24.INSTALL REAR SEATBACK COVER

a.

Attach the 4 claws to install the rear seatback cover.


Hide 73373 25.INSTALL REAR SEAT SHOULDER BELT COVER

a.

Connect the outer belt to the rear seat shoulder belt cover.


b.
B237669

Attach the 2 guides and 2 claws to install the rear seat shoulder belt cover.


Hide 73178A 26.INSTALL SEAT BELT ANCHOR COVER CAP

B237667

a.

Attach the 2 claws to install the seat belt anchor cover cap.


Hide 72058A 27.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

a.
B165026E06
1.688,2.948 1.948,3.167 0.26,0.219 10 false (1) 1.698,2.229 1.948,2.427 0.25,0.198 10 true (2) 0.365,0.833 0.625,1.052 0.26,0.219 10 false (3)

Connect the cable in the order shown in the illustration to install the rear seat lock control lever sub-assembly LH.


b.

Install the 2 screws.


Hide 72572C 28.INSTALL RECLINING ADJUSTER KNOB CAP LH

B237664

a.

Attach the guide and claw to install the reclining adjuster knob cap LH.


Hide 73390C 29.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

a.
B237670C03
0.198,1.979 0.344,1.979 0.344,1.979 0.49,2.75 true 3.26,0.135 3.104,0.135 3.104,0.135 2.844,0.708 true 0.052,1.885 0.208,2.063 0.156,0.177 10 false *a 3.25,0.052 3.406,0.229 0.156,0.177 10 false *a
*a Protruding Part


Install the rear No. 1 seat inner belt assembly LH and connect the rear No. 1 seat 3 point type belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Do not allow the anchor parts of the rear No. 1 seat 3 point type belt assembly LH and rear No. 1 seat inner belt assembly LH to overlap the protruding parts of the seat cushion frame.



b.
B613932

w/ Seat Belt Warning System:

i.

Attach the clamp and connect the connector.

NOTICE:

Pass the harness through between cushion frame and cushion wire.




Hide 72978 30.INSTALL CENTER NO. 2 SEATBACK COVER

a.

Install the center No. 2 seatback cover with the 3 screws.


Hide 74633A 31.INSTALL COAT HOOK CAP

B237661

a.

Attach the guide and 2 claws to install the coat hook cap.


Hide 79873 32.INSTALL FOLD SEATBACK WIRE

a.

Attach the 2 claws to install the fold seatback wire.


Hide 72663 33.INSTALL REAR NO. 1 SEAT LOCK CONTROL LEVER

B237658

a.

Install the rear No. 1 seat lock control lever as shown in the illustration.


Hide 72660F 34.INSTALL REAR SEAT LOCK ASSEMBLY LH

a.

Install the rear seat lock assembly LH with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the clamp to connect the wire.


Hide 79157 35.INSTALL NO. 1 SEATBACK COVER

a.
B237655

Attach the guide.


b.
B237653

Attach the 2 claws to install the No. 1 seatback cover.


Hide 71931A 36.INSTALL REAR SEAT HEADREST SUPPORT

a.

Attach the 4 claws to install the 2 rear seat headrest supports.


Hide 72877C 37.INSTALL SEAT ARMREST COVER

a.
B237649

Install the seat armrest cover to the pad.


b.
B237648

Install the seat armrest cover with pad.


c.
B237646

Attach the hooks.


Hide 71087 38.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY

a.

Attach the 5 clips to install the rear seatback board sub-assembly.


Hide 72665B 39.INSTALL REAR SEATBACK LOCK COVER

B237643

a.

Move the rear seatback lock cover in the direction of the arrow to attach the clip and 2 guides.


b.

Attach the claw.


Hide 72996A 40.INSTALL REAR SEATBACK COVER

a.

Attach the 4 claws to install the rear seatback cover.


Hide 72806B 41.INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY

B237640

a.

Attach the 2 claws to install the rear seat center armrest cup holder sub-assembly.


b.

Install the 2 screws.


Hide 72830 42.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

a.
B237637

Install the rear seat center armrest assembly as shown in the illustration.


b.

Install the armrest support with the nut.


c.

Using a T45 "TORX" socket wrench, install the rear seat center armrest assembly and 2 bushes with the 2 "TORX" bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 71349B 43.INSTALL REAR SEATBACK STAY COVER RH

a.

Attach the guide and 3 claws to install the rear seatback stay cover RH.


Hide 71369B 44.INSTALL REAR SEATBACK STAY COVER LH

a.

Attach the guide and 3 claws to install the rear seatback stay cover LH.


Hide 72731 45.INSTALL REAR SEAT RECLINING BRACKET RH

a.

Using a T45 "TORX" socket wrench, install the rear seat reclining bracket RH and bush with the "TORX" bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 72732 46.INSTALL REAR SEAT RECLINING BRACKET LH

a.

Using a T45 "TORX" socket wrench, install the rear seat reclining bracket LH and bush with the "TORX" bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 71397A 47.INSTALL CENTER SEAT HINGE COVER

B237631

a.

Attach the 2 guides and install the center seat hinge cover with the clip.


Hide 71960B 48.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY

a.

Install the rear seat center headrest assembly.


Hide 49.INSTALL CENTER SEATBACK ASSEMBLY

a.

Install the center seatback assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 71647 50.INSTALL REAR SEAT CUSHION EDGE PROTECTOR

a.

Install the rear seat cushion edge protector to the cushion spring.


Hide 87510P 51.INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71076S 52.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

a.

Set the separate type rear seat cushion cover in place.


b.
B237628C02
2.281,2.385 2.125,2.385 2.125,2.385 1.625,3.771 false 2.333,2.313 2.563,2.51 0.229,0.198 10 false *a
*a Hog Ring Pliers


Using hog ring pliers, install the separate type rear seat cushion cover to the separate type rear seat cushion pad with 14 new hog rings.

NOTICE:
·

Be careful not to damage the separate type rear seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.




Hide 71696 53.INSTALL REAR NO. 2 SEAT PROTECTOR

a.

Install the 2 rear No. 2 seat protectors to the separate type rear seat cushion pad.


Hide 54.INSTALL SEAT CUSHION COVER WITH PAD

a.
B237625

Attach the hook.


b.
B237623

Attach the hooks to install the seat cushion cover with pad.


c.

w/ Seat Heater System:

i.
B360133

Pass the wire harness as shown in the illustration.


ii.
B359313

Connect the 2 rear seat heater connectors.



Hide 72616A 55.INSTALL REAR SEATBACK LOCK STRIKER COVER LH

a.

Attach the 3 clips to install the rear seatback lock striker cover LH.


Hide 71826B 56.INSTALL REAR SEAT CUSHION MOULDING LH

B237620

a.

Move the rear seat cushion moulding LH in the direction of the arrow to attach the guide.


b.

Attach the 3 claws and clip to install the rear seat cushion moulding LH.


Hide 71395B 57.INSTALL CENTER SEAT HINGE COVER LH

B237618

a.

Attach the 2 guides and install the center seat hinge cover LH with the clip.


Hide 72526A 58.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.

Install the reclining adjuster release handle LH with the 3 screws.


Hide 71846A 59.INSTALL REAR SEAT UPPER RECLINING COVER LH

B237786

a.

Attach the 3 claws to install the rear seat upper reclining cover LH.