Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
71845A
1.REMOVE REAR SEAT UPPER RECLINING COVER RH
| *a | Protective Tape |
Using a screwdriver, detach the 3 claws and remove the rear seat upper reclining cover RH.
Tape the screwdriver tip before use.
72525B
2.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
Remove the 3 screws and reclining adjuster release handle RH.
71825B
3.REMOVE REAR SEAT CUSHION MOULDING RH
Using a clip remover, detach the clip.
Using a moulding remover, detach the 3 claws.
Move the rear seat cushion moulding RH in the direction of the arrow to detach the guide and remove the rear seat cushion moulding RH.
71829B
4.REMOVE REAR SEAT REAR CUSHION MOULDING LH
Remove the screw.
Using a moulding remover, detach the 3 claws.
Detach the 2 guides and remove the rear seat rear cushion moulding LH.
72615A
5.REMOVE REAR SEATBACK LOCK STRIKER COVER RH
Using a clip remover, detach the 3 clips and remove the rear seatback lock striker cover RH.
6.REMOVE SEAT CUSHION COVER WITH PAD
w/ Seat Heater System:
Disconnect the 2 rear seat heater connectors.
Pull out the wire harness as shown in the illustration.
| *a | Slit |
w/ Seat Belt Warning System:
Disconnect the connector and detach the clamp.
Pass the wire harness through the slit.
Detach the hooks and remove the seat cushion cover with pad.
73380C
7.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
73390A
8.REMOVE REAR SEAT INNER BELT ASSEMBLY
71696
9.REMOVE REAR NO. 2 SEAT PROTECTOR
Remove the 2 rear No. 2 seat protectors from the separate type rear seat cushion pad.
71647
10.REMOVE REAR SEAT CUSHION EDGE PROTECTOR
Remove the rear seat cushion edge protector from the cushion spring.
71075S
11.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the 14 hog rings and separate type rear seat cushion cover from the separate type rear seat cushion pad.
87510P
12.REMOVE REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
72572B
13.REMOVE RECLINING ADJUSTER KNOB CAP RH
| *a | Protective Tape |
Using a screwdriver, detach the claw and guide, and then remove the reclining adjuster knob cap RH.
Tape the screwdriver tip before use.
72057
14.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH
Remove the 2 screws.
Disconnect the cable in the order shown in the illustration and remove the rear seat lock control lever sub-assembly RH.
71845C
15.REMOVE REAR SEAT COVER CAP
Using a screwdriver, detach the claw and guide, and then remove the rear seat cover cap.
Tape the screwdriver tip before use.
72067A
16.REMOVE REAR CENTER BACK LOCK CONTROL LEVER
Remove the 2 screws.
Move the rear center back lock control lever in the direction of the arrow to detach the guide and remove the rear center back lock control lever.
Detach the cable clamp and disconnect the cable from the rear center back lock control lever.
72996A
17.REMOVE REAR SEATBACK COVER
Using a screwdriver, detach the 4 claws and remove the rear seatback cover.
Tape the screwdriver tip before use.
71880A
18.REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH
Using a clip remover, detach the 7 clips and remove the rear seatback board carpet assembly RH.
71931B
19.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.
20.REMOVE SEATBACK COVER WITH PAD
| *a | Hook |
| *b | Hog Ring |
Remove the 14 hog rings and detach the hooks, and then remove the seatback cover with pad.
w/ Seat Heater System:
Remove the wire harness.
71077S
21.REMOVE SEPARATE TYPE REAR SEATBACK COVER
w/ Seat Heater System:
Disconnect the rear seatback heater assembly wire harness from the separate type rear seatback pad.
Remove the 8 hog rings and separate type rear seatback cover from the separate type rear seatback pad.
87510Q
22.REMOVE REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
71697
23.REMOVE REAR SEATBACK EDGE PROTECTOR
Remove the rear seatback edge protector from the rear seatback frame sub-assembly RH.
71879C
24.REMOVE REAR SEAT INNER RECLINING COVER RH
Remove the 2 screws.
Detach the guide and remove the rear seat inner reclining cover RH.
71875J
25.REMOVE RECLINING ADJUSTER INSIDE COVER RH
Remove the 2 screws.
Detach the 2 claws and remove the reclining adjuster inside cover RH.
71876C
26.REMOVE RECLINING ADJUSTER INSIDE COVER RH
Using a clip remover, detach the clip.
Move the reclining adjuster inside cover RH in the direction of the arrow to detach the 2 claws and remove the reclining adjuster inside cover RH.
71875E
27.REMOVE RECLINING ADJUSTER INSIDE COVER RH
Detach the claw and guide, and remove the reclining adjuster inside cover RH.
71499C
28.REMOVE REAR SEAT CUSHION SPRING DAMPER
Remove the 2 nuts and rear seat cushion spring damper.
71499D
29.REMOVE REAR SEATBACK SPRING DAMPER (w/ Dynamic Damper)
Remove the 2 nuts and rear seatback spring damper.
72704A
30.REMOVE REAR SEAT RECLINING CONTROL CABLE
Cut off the 3 cable ties.
Detach the 2 cable clamps and disconnect the rear seat reclining control cable, and then remove the rear seat reclining control cable.
72704B
31.REMOVE REAR NO. 2 SEAT RECLINING CONTROL CABLE
Detach the cable clamp and disconnect the rear No. 2 seat reclining control cable, and then remove the rear No. 2 seat reclining control cable.
87501D
32.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
82193
33.REMOVE REAR SEAT WIRE RH (w/ Seat Wire Harness)
| *A | w/ Seat Belt Warning System |
Detach the claw and disconnect the rear seat wire connector.
Detach the clamp and remove the rear seat wire RH.
71246A
34.REMOVE REAR SEAT CUSHION SET PLATE
Remove the 2 nuts and rear seat cushion set plate.
72631
35.REMOVE REAR SEATBACK LOCK PLATE LH
Detach the 2 cable clamps and disconnect the cable.
Remove the nut and rear seatback lock plate LH.
71017
36.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY RH
Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and rear seatback frame sub-assembly RH.
72995A
37.REMOVE REAR SEAT COVER
Remove the screw and rear seat cover.
71461
38.REMOVE REAR SEAT CUSHION SPRING
Detach the 2 hooks and remove the rear seat cushion spring.
71015A
39.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH
| *1 | No. 1 Seat Leg Plate |
Remove the 6 nuts and rear seat cushion frame sub-assembly RH together with the No. 1 seat leg plate.
72173A
40.REMOVE REAR SEAT TRACK ADJUSTING HANDLE RH
Remove the seat cushion side frame sub-assembly RH.
Slide the slide rail to the rearmost position.
Using a small screwdriver, push down the handle stopper to detach the claw and remove the rear seat track adjusting handle RH.
Insert the screwdriver in the hole shown into the illustration while looking into the hole.