Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2021.06
RM27T0E _56 Audio / Visual / Telematics _056796 TELEMATICS _0277431 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B157111  Indicator (Green) Circuit Short to Ground  B157113  Indicator (Green) Circuit Open  


DESCRIPTION

This DTC is stored when the telephone transceiver assembly detects an open or short in the manual (SOS) switch green indicator circuit of the manual (SOS) switch.

The manual (SOS) switch green indicator illuminates for 5 seconds after the ignition switch is turned to ON.

If the telematics system is not active, the manual (SOS) switch green indicator will turn off.

If the telematics system is active, the manual (SOS) switch green indicator will blink while communicating with the call center.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157111 Indicator (Green) Circuit Short to Ground Manual (SOS) switch green indicator impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light assembly (manual [SOS] switch)

·

Harness or connector


B157113 Indicator (Green) Circuit Open Manual (SOS) switch green indicator impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light assembly (manual [SOS] switch)

·

Harness or connector



WIRING DIAGRAM

E467079E04
1.708,0.99 2.458,1.396 0.75,0.406 10 false GREEN 3.292,0.656 3.906,0.854 0.615,0.198 10 false IND2 3.271,1.094 3.885,1.292 0.615,0.198 10 false GND 0.792,2.354 4.135,2.729 3.344,0.375 10 false Map Light Assembly 5.156,0.656 5.469,0.854 0.313,0.198 10 false 22 5.49,0.771 6.104,0.969 0.615,0.198 10 false IND2 4.833,1.729 5.292,1.927 0.458,0.198 10 false G333 4.813,1.896 6.885,2.302 2.073,0.406 10 false Telephone Transceiver Assembly 0.813,2.188 1.271,2.385 0.458,0.198 10 false W7 1.104,1.75 4.448,2.125 3.344,0.375 10 false Manual (SOS) Switch 3.688,0.635 4.302,0.833 0.615,0.198 10 false 18 3.729,1.073 4.344,1.271 0.615,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH) (GREEN INDICATOR)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH) (GREEN INDICATOR)
a.
E467078C02
1.427,0.198 1.885,0.458 0.458,0.26 2.656,1.948 2.458,1.948 2.458,1.948 2.208,1.323 true 2.542,0.396 2.344,0.396 2.344,0.396 2.073,1.073 true 0.042,0.042 0.354,0.24 0.313,0.198 10 false *a 1.531,0.24 1.844,0.438 0.313,0.198 10 false W7 2.698,1.854 3.167,2.083 0.469,0.229 10 false IND2 2.604,0.281 3.073,0.51 0.469,0.229 10 false GND
*a Component without harness connected
(Map Light Assembly [Manual (SOS) Switch])


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect the positive (+) lead to terminal W7-18 (IND2) and the negative (-) lead to terminal W7-5 (GND) of the map light assembly connector.


d.

Check if the illumination for the manual (SOS) switch green indicator comes on.

OK:

Green indicator comes on.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL [SOS] SWITCH)

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G333 telephone transceiver assembly connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G333-22 (IND2) - W7-18 (IND2) Always Below 1 Ω
W7-5 (GND) - Body ground Always Below 1 Ω
G333-22 (IND2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT