Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2021.06
RM27T0E _56 Audio / Visual / Telematics _056796 TELEMATICS _0277431 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B157213  Microphone Circuit Open  


DESCRIPTION

This DTC is stored when a microphone signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157213 Microphone Circuit Open Current at terminal MCVD is lower than the malfunction threshold for 10 seconds or more while the ignition switch is ON
·

Telephone transceiver assembly

·

Communication telematics box

·

Mayday wire

·

Harness or connector



WIRING DIAGRAM

E405960E24
0.906,1.406 1.521,1.604 0.615,0.198 10 false MCMD 1.052,1.813 1.667,2.01 0.615,0.198 10 false SP+ 1.063,2.219 1.677,2.417 0.615,0.198 10 false SP- 0.99,2.594 1.604,2.792 0.615,0.198 10 false MICV 0.948,2.938 1.563,3.135 0.615,0.198 10 false MIC1+ 0.927,3.344 1.542,3.542 0.615,0.198 10 false MIC2+ 1.042,3.792 1.656,3.99 0.615,0.198 10 false MCI- 5.667,1.396 6.281,1.594 0.615,0.198 10 false MCMD 5.667,1.781 6.281,1.979 0.615,0.198 10 false SP+ 5.667,2.198 6.281,2.396 0.615,0.198 10 false SP- 5.656,2.583 6.271,2.781 0.615,0.198 10 false MICV 5.646,3 6.26,3.198 0.615,0.198 10 false MCVD 5.656,3.365 6.271,3.563 0.615,0.198 10 false MCI+ 5.656,3.771 6.271,3.969 0.615,0.198 10 false MCI- 5.531,4.792 6.948,5.135 1.417,0.344 10 false Telephone Transceiver Assembly 4.031,3.99 4.688,4.219 0.656,0.229 10 false * 0.375,4.75 1.438,5.156 1.063,0.406 10 false Communication Telematics Box 0.375,4.583 1.146,4.99 0.771,0.406 10 false P 2.104,1.302 2.719,1.5 0.615,0.198 10 false MCMD 2.26,1.698 2.875,1.896 0.615,0.198 10 false SP+ 2.302,2.104 2.917,2.302 0.615,0.198 10 false SP- 2.198,2.479 2.813,2.677 0.615,0.198 10 false MICV 2.219,3.302 2.833,3.5 0.615,0.198 10 false MIC2 2.219,2.906 2.833,3.104 0.615,0.198 10 false MIC1 2.229,3.677 2.844,3.875 0.615,0.198 10 false MCI- 1.458,1.313 2.073,1.51 0.615,0.198 10 false 1 1.479,1.708 2.094,1.906 0.615,0.198 10 false 3 1.469,2.104 2.083,2.302 0.615,0.198 10 false 8 1.479,2.5 2.094,2.698 0.615,0.198 10 false 5 1.5,3.292 2.115,3.49 0.615,0.198 10 false 7 1.5,2.896 2.115,3.094 0.615,0.198 10 false 2 1.49,3.677 2.104,3.875 0.615,0.198 10 false 4 2.76,1.219 3.375,1.417 0.615,0.198 10 false 1 2.76,1.615 3.375,1.813 0.615,0.198 10 false 3 2.76,2 3.375,2.198 0.615,0.198 10 false 9 2.792,2.406 3.406,2.604 0.615,0.198 10 false 6 2.74,2.792 3.354,2.99 0.615,0.198 10 false 10 2.75,3.198 3.365,3.396 0.615,0.198 10 false 11 2.771,3.594 3.385,3.792 0.615,0.198 10 false 5 5.344,1.677 5.958,1.875 0.615,0.198 10 false 18 5.385,1.292 6,1.49 0.615,0.198 10 false 8 5.354,2.073 5.969,2.271 0.615,0.198 10 false 34 5.354,2.458 5.969,2.656 0.615,0.198 10 false 24 5.396,2.865 6.021,3.063 0.625,0.198 10 false 5 5.396,3.656 6.021,3.854 0.625,0.198 10 false 7 5.531,4.604 6.302,5.01 0.771,0.406 10 false G333 2.677,1.396 3.448,1.802 0.771,0.406 10 false W25 5.646,4.198 6.26,4.396 0.615,0.198 10 false SGND 5.354,4.083 5.979,4.281 0.625,0.198 10 false 23 1.667,4.615 2.781,5.094 1.115,0.479 10 false Mayday Wire 5.396,3.26 6.021,3.458 0.625,0.198 10 false 6 0.344,5.458 2.521,5.781 2.177,0.323 10 false *: Shielded 2.677,1.802 3.448,2.208 0.771,0.406 10 false W25 2.688,2.188 3.458,2.594 0.771,0.406 10 false W25 2.677,2.583 3.448,2.99 0.771,0.406 10 false W25 2.688,2.979 3.458,3.385 0.771,0.406 10 false W25 2.677,3.375 3.448,3.781 0.771,0.406 10 false W25 2.667,3.771 3.438,4.177 0.771,0.406 10 false W25

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAYDAY WIRE)
2.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAYDAY WIRE)
a.

Disconnect the G333 telephone transceiver assembly connector.


b.

Disconnect the W25 mayday wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G333-8 (MCMD) - W25-1 (MCMD) Always Below 1 Ω
G333-18 (SP+) - W25-3 (SP+) Always Below 1 Ω
G333-34 (SP-) - W25-9 (SP-) Always Below 1 Ω
G333-24 (MICV) - W25-6 (MICV) Always Below 1 Ω
G333-5 (MCVD) - W25-10 (MIC1) Always Below 1 Ω
G333-6 (MCI+) - W25-11 (MIC2) Always Below 1 Ω
G333-7 (MCI-) - W25-5 (MCI-) Always Below 1 Ω
G333-8 (MCMD) or W25-1 (MCMD) - Body ground Always 10 kΩ or higher
G333-18 (SP+) or W25-3 (SP+) - Body ground Always 10 kΩ or higher
G333-34 (SP-) or W25-9 (SP-) - Body ground Always 10 kΩ or higher
G333-24 (MICV) or W25-6 (MICV) - Body ground Always 10 kΩ or higher
G333-5 (MCVD) or W25-10 (MIC1) - Body ground Always 10 kΩ or higher
G333-6 (MCI+) or W25-11 (MIC2) - Body ground Always 10 kΩ or higher
G333-7 (MCI-) or W25-5 (MCI-) - Body ground Always 10 kΩ or higher
G333-23 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)
a.
B617679C02
1.49,2.823 1.865,3.083 0.375,0.26 1.5,0.448 1.875,0.708 0.375,0.26 2.177,1.458 2.646,1.458 true 1.313,3.208 1.708,3.729 true 1.823,1.448 2.542,0.708 true 1.823,1.688 2.479,2.115 true 0.781,1.438 1.26,1.438 true 1.615,1.688 0.938,2.177 true 1.438,1.688 0.781,1.833 true 1.438,1.427 0.844,0.948 true 1,3.396 1.49,3.729 true 0.917,3.771 1.302,3.771 true 1.719,4 1.854,4.365 true 2.25,3.292 1.917,3.719 true 1.313,4.333 1.531,3.979 true 2.5,3.76 2.073,3.76 true 0.365,2.635 0.677,2.833 0.313,0.198 10 false *b 0.292,0.26 0.604,0.458 0.313,0.198 10 false *a 1.646,2.865 1.958,3.063 0.313,0.198 10 false P 1.563,0.5 1.875,0.698 0.313,0.198 10 false W25 2.688,1.375 3.271,1.75 0.583,0.375 10 false MCMD 0.448,3.688 1.031,4.063 0.583,0.375 10 false MCMD 2.583,0.625 3.167,1 0.583,0.375 10 false SP+ 2.531,2.073 3.115,2.448 0.583,0.375 10 false SP- 0.417,1.344 1,1.719 0.583,0.375 10 false MICV 0.396,1.75 0.896,2.104 0.5,0.354 10 false MIC2 0.479,0.844 1.063,1.219 0.583,0.375 10 false MCI- 0.542,2.115 1.125,2.49 0.583,0.375 10 false MIC1 1.063,3.063 1.646,3.438 0.583,0.375 10 false SP+ 0.563,3.313 1.146,3.688 0.583,0.375 10 false MIC1+ 1.896,4.323 2.531,4.656 0.635,0.333 10 false SP- 2.542,3.698 3.125,4.073 0.583,0.375 10 false MICV 0.927,4.313 1.427,4.667 0.5,0.354 10 false MIC2+ 2.229,3.135 2.813,3.51 0.583,0.375 10 false MCI-
*a Front view of wire harness connector
(to Wire Harness)
*b Front view of wire harness connector
(to Communication Telematics Box)


Disconnect the W25 wire harness connector.


b.

Disconnect the P communication telematics box connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W25-1 (MCMD) - P-1 (MCMD) Always Below 1 Ω
W25-3 (SP+) - P-3 (SP+) Always Below 1 Ω
W25-9 (SP-) - P-8 (SP-) Always Below 1 Ω
W25-6 (MICV) - P-5 (MICV) Always Below 1 Ω
W25-10 (MIC1) - P-2 (MIC1+) Always Below 1 Ω
W25-11 (MIC2) - P-7 (MIC2+) Always Below 1 Ω
W25-5 (MCI-) - P-4 (MCI-) Always Below 1 Ω
W25-1 (MCMD) or P-1 (MCMD) - Body ground Always 10 kΩ or higher
W25-3 (SP+) or P-3 (SP+) - Body ground Always 10 kΩ or higher
W25-9 (SP-) or P-8 (SP-) - Body ground Always 10 kΩ or higher
W25-6 (MICV) or P-5 (MICV) - Body ground Always 10 kΩ or higher
W25-10 (MIC1) or P-2 (MIC1+) - Body ground Always 10 kΩ or higher
W25-11 (MIC2) or P-7 (MIC2+) - Body ground Always 10 kΩ or higher
W25-5 (MCI-) or P-4 (MCI-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY

NG

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.
E442560C18
1.385,0.573 1.958,0.885 0.573,0.313 2.26,1.948 2.458,2.74 2.458,2.74 2.625,2.74 true 2.292,1.813 2.563,0.969 2.563,0.969 2.729,0.969 true 0.25,0.302 0.563,0.5 0.313,0.198 10 false *a 1.521,0.646 2.063,0.865 0.542,0.219 10 false G333 2.802,0.896 3.344,1.115 0.542,0.219 10 false MCI- 2.677,2.667 3.219,2.885 0.542,0.219 10 false MICV
*a Component with harness connected
(Telephone Transceiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G333-24 (MICV) - Body ground Ignition switch ON 4 to 6 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G333-7 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK COMMUNICATION TELEMATICS BOX

NG

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
5.CHECK COMMUNICATION TELEMATICS BOX
a.

Replace the communication telematics box with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL


b.

Turn the ignition switch to ON and wait for 10 seconds or more.



d.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION TELEMATICS BOX IS DEFECTIVE)

NG

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT