Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › from 2021.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P203A96  Reductant Level Sensor "A" Circuit Component Internal Failure  P204A12  Reductant Pressure Sensor Circuit High Circuit Short to Battery  P204A14  Reductant Pressure Sensor Circuit Low Circuit Short to Ground or Open  P205A11  Reductant Tank Temperature Sensor Circuit Low Circuit Short to Ground  P205A15  Reductant Tank Temperature Sensor Circuit High Circuit Short to Battery or Open  P206A87  Reductant Quality Sensor Circuit Missing Message  P206A96  Reductant Quality Sensor Circuit Component Internal Failure  P208A12  Reductant Pump "A" Control Circuit High Circuit Short to Battery  P208A14  Reductant Pump "A" Control Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

The urea pump assembly (urea pump control ECU integrated urea pump) is a bottom entry type in-tank pump installed to the bottom of the urea tank assembly. It contains a UTLC sensor* that uses ultrasonic waves, a urea pump, a urea tank heater and a urea pressure sensor. It is integrated with the urea pump assembly (urea pump control ECU integrated urea pump) to provide the following functions.

HINT:

The UTLC sensor uses ultrasonic waves to send the temperature, level and quality (concentration) of urea as status signals to the urea pump assembly (urea pump control ECU integrated urea pump) using SENT communication.

·

A pump to pressurize and supply the urea solution

·

A heating function to thaw the urea solution and to warm it up to prevent it from freezing

·

A level gauge to measure the urea solution amount in the tank

·

A urea solution quality check to detect a decrease in the concentration of urea in the tank

·

A filter for collecting the foreign matter in the urea solution tank

·

Diagnosis function integrated with the urea pump control ECU to detect malfunctions in sensors and actuators



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P203A96 Reductant Level Sensor "A" Circuit Component Internal Failure An internal malfunction occurs in the urea solution level sensor for 3 seconds or more.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P203A
P204A12 Reductant Pressure Sensor Circuit High Circuit Short to Battery An open or short circuit occurs in the pressure sensor circuit for 3 seconds or more.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P204D
P204A14 Reductant Pressure Sensor Circuit Low Circuit Short to Ground or Open An open or short circuit occurs in the pressure sensor circuit for 3 seconds or more.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P204C
P205A11 Reductant Tank Temperature Sensor Circuit Low Circuit Short to Ground An open or short circuit occurs in the temperature sensor circuit for 3 seconds or more.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P205C
P205A15 Reductant Tank Temperature Sensor Circuit High Circuit Short to Battery or Open An open or short circuit occurs in the temperature sensor circuit for 3 seconds or more.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P205D
P206A87 Reductant Quality Sensor Circuit Missing Message A malfunction occurs during urea pump assembly (urea pump control ECU integrated urea pump) communication with the UTLC sensor for 3 seconds or more.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P206A
P206A96 Reductant Quality Sensor Circuit Component Internal Failure An internal malfunction occurs in the urea solution level sensor when the ignition switch is turned to ON.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P206A
P208A12 Reductant Pump "A" Control Circuit High Circuit Short to Battery When the urea pump motor is operating, an open or short circuit occurs in the urea pump motor circuit for 3 seconds or more.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P208D
P208A14 Reductant Pump "A" Control Circuit Low Circuit Short to Ground or Open When the urea pump motor is operating, an open or short circuit occurs in the urea pump motor circuit for 3 seconds or more.
(1 trip detection logic)
Urea pump assembly (urea pump control ECU integrated urea pump) Comes on DTC stored SAE Code: P208C

Related Data List
DTC No. Data List
P203A96 -
P204A12
P204A14
Reductant Pressure
P205A11
P205A15
Reductant Tank Temperature
P206A87
P206A96
-
P208A12
P208A14
Reductant Pump

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P203A96
P204A12
P204A14
P205A11
P205A15
P206A87
P206A96
P208A12
P208A14
Engine switch on (IG) for 3 seconds

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.

Replace the urea pump assembly (urea pump control ECU integrated urea pump).

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Turn the engine switch on (IG) and wait for 3 seconds or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END