Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for LED Headlight) › from 2021.06
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0326212 LIGHTING SYSTEM(for LED Headlight) C

LIGHTING (EXT)  LIGHTING SYSTEM(for LED Headlight)  B242E  Open in IG Circuit  


DESCRIPTION

This DTC is stored when a malfunction occurs in the No. 1 headlight ECU sub-assembly LH IG power source circuit. The No. 1 headlight ECU sub-assembly LH stores DTC B242E.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B242E Open in IG Circuit Open in the No. 1 headlight ECU sub-assembly LH IG power source circuit
·

Harness or connector

·

No. 1 headlight ECU sub-assembly LH


-

WIRING DIAGRAM

E374281E07
4.479,2.031 7.021,2.427 2.542,0.396 10 false A130 4.49,2.208 7.031,2.604 2.542,0.396 10 false No. 1 Headlight ECU Sub-assembly LH 5.208,1.354 5.927,1.573 0.719,0.219 10 false GND 5.208,0.833 5.927,1.052 0.719,0.219 10 false IG 3.885,1.042 4.896,1.333 1.01,0.292 10 false ECU-IG NO.3 1.604,0.802 3.24,1.052 1.635,0.25 10 false from IG NO.4 Relay 4.979,0.719 5.49,1 0.51,0.281 10 false 4 4.896,1.281 5.406,1.563 0.51,0.281 10 false 12

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the No. 1 headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the No. 1 headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>REGISTRATION



PROCEDURE

1.CHECK FOR DTC

b.

Turn the ignition switch to ON.


c.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR

OK:

DTC B242E is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - BATTERY AND BODY GROUND)
a.
E380658C11
1.396,0.115 1.844,0.365 0.448,0.25 1.375,1.875 1.188,1.875 1.188,1.875 0.833,1.354 true 0.99,0.333 1.156,0.333 1.156,0.333 1.792,1.167 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.458,0.146 1.938,0.406 0.479,0.26 10 false A130 0.792,0.208 1.26,0.375 0.469,0.167 10 false IG 1.427,1.75 1.896,1.917 0.469,0.167 10 false GND
*a Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly LH)


Disconnect the No. 1 headlight ECU sub-assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A130-4 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A130-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR