Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › from 2021.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P207F00  Reductant Quality Performance  


DESCRIPTION

This DTC is stored when the urea solution concentration calculated by the quality sensor built into the urea pump assembly (urea pump control ECU integrated urea pump) is the specified value or less.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P207F00 Reductant Quality Performance When all of the following conditions are met and the vehicle is stopped 3 times for 30 seconds or more each time:
·

Urea solution temperature is 0°C or more but below 60°C

·

The vehicle is stopped after repeatedly driving and stopping the vehicle the predetermined amount of times with the urea solution amount at the specified value or more

·

The urea solution concentration is the specified value or less


(2 trip detection logic)
·

Urea solution

·

Urea pump assembly (urea pump control ECU integrated urea pump)


Does not come on DTC stored SAE Code: P207F

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P207F00 After starting the engine with the urea solution temperature from 0°C to less than 60°C, drive*1 and then stop*2 the vehicle 3 times or more
(Perform the procedure above for 2 trips)
HINT:
·

*1: Drive the vehicle at 5 km/h or higher for 60 seconds or more

·

*2: Stop the vehicle for 30 seconds or more continuously (any driving position may be used as long as the vehicle speed is 0 km/h)




CAUTION / NOTICE / HINT

NOTICE:
Handling urea solution
·

Wear protective equipment as necessary (protective glasses and gloves).

·

Do not dilute urea solution.

·

If urea solution contacts your eyes or skin, immediately wash the contacted area with a large amount of water and consult a doctor as necessary.

·

If urea solution dries, it deposits a white powder. Also, if urea solution contacts metals such as copper and aluminum for a long period of time, it may promote corrosion. Therefore, if urea solution is spilled, dampen a cloth or other item and wipe it up or rinse the area with cool or warm water.


Handling the urea injector set
·

The urea injector set is a precision instrument. Take necessary precautions for installation and shipping. Do not use the part if it has been struck or dropped.

·

If the urea solution remaining inside the urea injector set dries out, it may become unable to inject urea solution. Therefore, conduct urea tube with heater assembly installation and removal quickly.

·

If the urea solution dries out and deposition occurs, urea may cling to the O-ring of the pipe and cause seal problems. Therefore, clean the urea tube with heater assembly and intake port of the urea injector set with water before attaching them.

·

Perform this procedure in an environment where urea solution will not freeze.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.DRAIN UREA SOLUTION
HINT:

Drain the appropriate amount of urea solution in order to check the urea solution concentration.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Pump Check (Backward).

Powertrain > Engine and Transmission > Active Test
Tester Display
Reductant Pump Check (Backward)
50004 456 16

d.

Perform the Active Test.


e.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Purge.

Powertrain > Engine and Transmission > Active Test
Tester Display
Reductant Purge
50004 456 17

f.

Perform the Active Test.

HINT:

Perform the Reductant Purge to draw the urea solution back into the urea tank sub-assembly from the urea injector set.



g.

After performing the Active Test, remove the urea tube with heater assembly from the urea injector set.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA INJECTOR>REMOVAL

HINT:

If the urea solution remaining inside the urea injector set dries out, it may become unable to inject urea solution.


Therefore, seal the urea injector set with an item such as a cover or rubber cap so that the inside does not dry out.


h.

Prepare a bucket or other receptacle for collecting urea solution from the urea tube with heater assembly.


i.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Discharge.

Powertrain > Engine and Transmission > Active Test
Tester Display
Reductant Discharge
50004 456 14

j.

Perform the Active Test to drain the appropriate amount of the urea solution.


Result:
Proceed to
NEXT



NEXT

2.CHECK UREA SOLUTION
2.CHECK UREA SOLUTION
a.

Measure the concentration of urea solution by the urea concentration meter in the urea solution tank.


Standard:
Condition Specified Condition
Urea solution temperature:
-8 to 40°C
Normal urea solution concentration:
28.4 to 35.2%


Result:
Proceed to
OK
NG



OK

3.INSPECT UREA TANK SUB-ASSEMBLY

NG

10.REPLACE UREA SOLUTION
3.INSPECT UREA TANK SUB-ASSEMBLY
a.

Remove the urea tank sub-assembly.


b.

Drain the urea solution and check the urea tank for foreign matter.


Standard:

No foreign matter in the urea tank


Result:
Proceed to
OK
NG



OK

4.INSPECT UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)

NG

9.CLEAN UREA TANK SUB-ASSEMBLY
4.INSPECT UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.

Check for dirt, blockage or damage to the sensing part of the urea quality sensor in the urea pump assembly (urea pump control ECU integrated urea pump).


Standard:

No dirt, blockage or damage to the sensing part of the urea quality sensor


Result:
Proceed to
OK
NG



OK

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

6.REPAIR OR REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

After starting the engine with the urea solution temperature from 0°C to less than 60°C, drive the vehicle at 5 km/h or higher for 60 seconds or more and then stop the vehicle for 30 seconds or more. Repeat this procedure at least 3 times.


e.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

f.

Confirm that the DTCs are not output again.


Result:
Proceed to
OK
NG



OK

END

NG

7.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
6.REPAIR OR REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.

Clean the sensing part of the urea quality sensor in the urea pump assembly (urea pump control ECU integrated urea pump) and then install it correctly.

HINT:

Replace the urea pump assembly (urea pump control ECU integrated urea pump) if it is damaged.



Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
a.

Replace the urea pump assembly (urea pump control ECU integrated urea pump).


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

After starting the engine with the urea solution temperature from 0°C to less than 60°C, drive the vehicle at 5 km/h or higher for 60 seconds or more and then stop the vehicle for 30 seconds or more. Repeat this procedure at least 3 times.


e.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

f.

Confirm that the DTCs are not output again.


Result:
Proceed to
NEXT



NEXT

END

9.CLEAN UREA TANK SUB-ASSEMBLY
a.

Remove foreign matter from the urea tank sub-assembly and clean it.

NOTICE:

Clean the urea tank with fresh water or dilute urea solution.



Result:
Proceed to
NEXT



NEXT

4.INSPECT UREA PUMP ASSEMBLY (UREA PUMP CONTROL ECU INTEGRATED UREA PUMP)
10.REPLACE UREA SOLUTION
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Pump Check (Backward).

Powertrain > Engine and Transmission > Active Test
Tester Display
Reductant Pump Check (Backward)
50004 456 16

d.

Perform the Active Test.


e.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Purge.

Powertrain > Engine and Transmission > Active Test
Tester Display
Reductant Purge
50004 456 17

f.

Perform the Active Test.

HINT:

Perform the Reductant Purge to draw the urea solution back into the urea tank sub-assembly from the urea injector set.



g.

After performing the Active Test, remove the urea tube with heater assembly from the urea injector set.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA INJECTOR>REMOVAL

HINT:

If the urea solution remaining inside the urea injector set dries out, it may become unable to inject urea solution.


Therefore, seal the urea injector set with an item such as a cover or rubber cap so that the inside does not dry out.


h.

Prepare a bucket or other receptacle for collecting urea solution from the urea tube with heater assembly.


i.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Discharge.

Powertrain > Engine and Transmission > Active Test
Tester Display
Reductant Discharge
50004 456 14

j.

Perform the Active Test to drain all the urea solution.


k.

After fully draining the urea solution, refill with AdBlue (conforming to ISO 22241-1) to the full level.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA TANK>REFILL

HINT:

Adding too little may prevent proper detection.



Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED