Home › Engine / Hybrid System › 5L-E (LUBRICATION) › OIL AND OIL FILTER › from 2021.06
RM27T0E _51 Engine / Hybrid System _053688 5L-E LUBRICATION _0260693 OIL AND OIL FILTER A

5L-E LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with mineral oil will result in the loss of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash the area thoroughly with soap and waterless hand cleaner. Never use gasoline, thinners or solvents to wash the skin.

·

In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



PROCEDURE

Hide 51457F 1.REMOVE ENGINE UNDER COVER SEAL

a.

Remove the 2 bolts and engine under cover seal.


Hide 2.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil drain plug and gasket, and then drain the oil into a container.


c.

Clean the drain plug and install it with a new gasket.

Torque:
35 N*m (352 kgf*cm, 25 ft.*lbf)


Hide 51450 3.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

Hide 15601 4.REMOVE OIL FILTER SUB-ASSEMBLY

a.
A227791E03
1.104,1.698 1.198,1.688 1.198,1.688 1.729,1.167 false 1.104,1.698 1.198,1.688 1.198,1.688 1.729,1.167 true 0.76,1.615 1.094,1.792 0.333,0.177 10 true SST

Using SST, remove the oil filter.

SST
09228-44011  


Hide 15601 5.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter.


c.

Install the oil filter and tighten it by hand until the gasket contacts the installation surface.


d.

Using SST, tighten the oil filter. Choose from the following to further tighten the oil filter.

SST
09228-44011  

i.
A227790E02
1.188,1.719 1.313,1.719 1.313,1.719 1.729,1.365 true 0.854,1.635 1.177,1.823 0.323,0.188 10 true SST

Using a torque wrench, tighten the oil filter.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


ii.

Tighten the oil filter a 3/4 turn by hand or with a common wrench.

Text in Illustration
V100136

3/4 turn



Hide 6.ADD ENGINE OIL

a.

Add fresh engine oil.

Standard Engine Oil:
Oil Grade Oil Viscosity (SAE)
API CF-4, CF or ACEA B3, B4, B5 or JASO DL-0 5W-30
10W-30


Standard Capacity (OIL FILTER SUB-ASSEMBLY 15600-41010):
Item Specified Condition
Drain and refill without oil filter change 6.0 liters (6.3 US qts, 5.3 Imp. qts)
Drain and refill with oil filter change 6.9 liters (7.3 US qts, 6.1 Imp. qts)
Dry fill 7.6 liters (8.0 US qts, 6.7 Imp. qts)


Standard Capacity (OIL FILTER SUB-ASSEMBLY 90915-40002):
Item Specified Condition
Drain and refill without oil filter change 6.0 liters (6.3 US qts, 5.3 Imp. qts)
Drain and refill with oil filter change 6.5 liters (6.9 US qts, 5.7 Imp. qts)
Dry fill 7.3 liters (7.7 US qts, 6.4 Imp. qts)



b.

Install the oil filler cap.


Hide 7.INSPECT FOR ENGINE OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


Hide 51450 8.INSTALL REAR ENGINE UNDER COVER ASSEMBLY

Hide 51457F 9.INSTALL ENGINE UNDER COVER SEAL

a.

Install the engine under cover seal with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)