Home › Engine / Hybrid System › 5L-E (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.08
RM27T0E _51 Engine / Hybrid System _053661 5L-E ENGINE MECHANICAL _0260483 ENGINE ASSEMBLY A

5L-E ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 74481 2.REMOVE BATTERY HOLD DOWN CLAMP

a.
A224625

Remove the nut and disconnect the engine wire.


b.

Remove the 2 nuts and battery hold down clamp.


Hide 28800 3.REMOVE BATTERY

Hide 74431 4.REMOVE BATTERY TRAY

Hide 53301 5.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose.


b.
A222363

Remove the 8 bolts and hood.

NOTICE:

If the hood support is detached from the ball joint, it become non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.



Hide 55781E 6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Remove the cowl top ventilator louver (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


Hide 53292A 7.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 52129B 8.REMOVE FRONT BUMPER COVER LOWER

a.

Remove the clip, 5 bolts and front bumper cover lower.


Hide 51405A 9.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.

Remove the 4 bolts.


b.
A224743

Unhook the engine under cover from the vehicle body as shown in the illustration.


Hide 51495 10.REMOVE TRANSMISSION UNDER COVER

a.

Remove the 2 bolts and transmission under cover.


Hide 51450 11.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

a.

Remove the 4 bolts and rear engine under cover.


Hide 53736 14.REMOVE FRONT FENDER APRON SEAL RH

a.

Remove the 4 clips and fender apron seal.


Hide 53736B 15.REMOVE NO. 1 FRONT FENDER APRON TO FRAME SEAL RH

a.

Remove the 5 clips and frame seal.


Hide 53737B 16.REMOVE FRONT FENDER APRON SEAL LH

a.

Remove the 5 clips and fender apron seal.


Hide 53737A 17.REMOVE NO. 1 FRONT FENDER APRON TO FRAME SEAL LH

a.

Remove the 5 clips and frame seal.


Hide 18.REMOVE RESONATOR WITH AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 19.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17700 20.REMOVE AIR CLEANER CASE ASSEMBLY

a.
A224627

Remove the 3 bolts and air cleaner case.


Hide 52521 22.REMOVE FRONT UPPER BUMPER RETAINER

Hide 53294C 23.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 53293C 24.REMOVE RADIATOR SIDE DEFLECTOR RH

Hide 16571C 25.REMOVE NO. 1 RADIATOR HOSE

Hide 16572D 26.REMOVE NO. 2 RADIATOR HOSE

Hide 16400 28.REMOVE RADIATOR ASSEMBLY

Hide 88320 30.DISCONNECT COOLER COMPRESSOR ASSEMBLY

a.
A225293

Remove the 4 bolts and idle pulley bracket.


b.
A224370

Disconnect the connector.


c.

Remove the 3 bolts and disconnect the cooler compressor.

HINT:

It is not necessary to completely remove the cooler compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



Hide 55550 32.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

a.

Hide 82121 33.DISCONNECT ENGINE WIRE

a.
A224626

Remove the 3 bolts, detach the clamp and disconnect the engine wire.


b.

Remove the No. 1 relay block cover.


c.
A224629

Remove the nut and detach the 2 claws.


d.

Disconnect the connector.


e.

Detach the 2 clamps and disconnect the engine wire.


f.
A225291

for LHD:

Detach the 4 clamps.


g.
A225401E06
1.979,0.031 2.25,0.25 0.271,0.219 12 true *B 0.042,0.031 0.333,0.26 0.292,0.229 12 true *A

Detach the grommet from the wire harness support.

Text in Illustration
*A for LHD
*B for RHD


h.
A225402E06
0.063,0.073 0.344,0.292 0.281,0.219 12 false *A 1.823,0.063 2.115,0.281 0.292,0.219 12 false *B

Detach the 4 claws to remove the wire harness support from the vehicle, and then pull out the ECM connector to remove it from the vehicle.

Text in Illustration
*A for LHD
*B for RHD


i.
A225509E02
0.073,0.083 0.365,0.302 0.292,0.219 12 false *A 0.083,2.51 0.396,2.729 0.313,0.219 12 false *B

Detach the clamp and disconnect the 5 connectors as shown in the illustration.

Text in Illustration
*A for LHD
*B for RHD


Hide 82715 34.REMOVE WIRING HARNESS CLAMP BRACKET (for LHD)

a.
A225292

Remove the bolt and wiring harness clamp bracket.


Hide 87245A 35.DISCONNECT HEATER WATER HOSE ASSEMBLY

a.
A224705E02
0.229,2.5 0.531,2.719 0.302,0.219 10 false *A

Remove the bolt and disconnect the heater water hoses.

Text in Illustration
*A for Rear Heater


Hide 77310A 36.LOOSEN FUEL TANK CAP ASSEMBLY

Hide 23770B 38.DISCONNECT FUEL HOSE

a.
A121131

Disconnect the 2 fuel hoses.


Hide 44320 39.DISCONNECT VANE PUMP ASSEMBLY

a.
A071326E04
1.073,0.469 1.24,0.469 1.24,0.469 1.469,0.917 true 0.74,0.385 1.063,0.563 0.323,0.177 10 true SST

Using SST, hold the pulley and loosen the nut.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Remove the nut and vane pump pulley from the vane pump shaft.


c.

Remove the 2 bolts and nut and disconnect the vane pump.

HINT:

Disconnect the vane pump from the vehicle with the hoses connected, and hang it with a rope.



Hide 31470 40.REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY

Hide 17410 43.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 46.REMOVE MANUAL TRANSMISSION ASSEMBLY

Hide 12371 47.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

NOTICE:

Perform this procedure when replacement of the engine mounting insulator is necessary.


a.
A225172

Remove the 4 bolts and rear engine mounting insulator from the transmission.


Hide 31210 48.REMOVE CLUTCH COVER ASSEMBLY

Hide 31250 49.REMOVE CLUTCH DISC ASSEMBLY

Hide 13405 50.REMOVE FLYWHEEL SUB-ASSEMBLY

A058716E04
1.052,0.615 0.698,1.417 0.698,1.417 1.01,0.948 true 0.531,1.469 0.875,1.667 0.344,0.198 10 true SST

a.

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Remove the 8 bolts and flywheel.


Hide 11355 51.REMOVE REAR END PLATE

a.

Remove the 2 bolts and rear end plate.


Hide 11354 52.REMOVE FLYWHEEL HOUSING DUST SEAL

Hide 53.INSTALL ENGINE HANGER

a.
A225772E03
1.156,0.156 1.01,0.156 1.01,0.156 0.823,0.854 true 2.51,0.146 2.615,0.146 2.615,0.146 2.927,0.719 true 2.292,0.063 2.51,0.26 0.219,0.198 10 false *1 1.229,0.073 1.448,0.271 0.219,0.198 10 true *2

Install an engine hanger to each location shown in the illustration.

Text in Illustration
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger

HINT:
No. 1 Engine Hanger 12281-54080
No. 2 Engine Hanger 12282-54070
Bolt (No. 1 Engine Hanger) 90119-10736
Bolt (No. 2 Engine Hanger) 91622-61022


Torque:
for No. 1 Engine Hanger : 59 N*m (602 kgf*cm, 44 ft.*lbf)
for No. 2 Engine Hanger : 37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Install the engine hangers with new bolts.



Hide 54.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.
A226979E02
0.229,0.146 0.458,0.344 0.229,0.198 10 true *1 1.854,0.146 2.052,0.333 0.198,0.188 10 true *2

Remove the 4 nuts and 4 bolts from the front engine mounting insulator LH and RH.

Text in Illustration
*1 for RH Side
*2 for LH Side


c.

Remove the engine by operating the engine sling device and chain block.


Hide 55.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine to an engine stand with bolts.


b.

Remove engine hanger.


Hide 56.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine.


Hide 12361 57.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A226990

Remove the 2 nuts and 2 front engine mounting insulators.