Home › Engine / Hybrid System › 2TR-FE (LUBRICATION) › OIL AND OIL FILTER › from 2021.06
RM27T0E _51 Engine / Hybrid System _053686 2TR-FE LUBRICATION _0260683 OIL AND OIL FILTER A

2TR-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the loss of natural oil from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash the area thoroughly with soap and waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

·

In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



PROCEDURE

Hide 51457F 1.REMOVE ENGINE UNDER COVER SEAL

a.

Remove the 2 bolts and engine under cover seal.


Hide 2.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil pan drain plug and gasket, and drain the oil into a container.


Hide 51450 3.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

Hide 15601 4.REMOVE OIL FILTER SUB-ASSEMBLY

a.
G038461E04
2.063,0.99 2.688,1.26 true 2.771,1.188 3.083,1.354 0.313,0.167 10 false SST

Using SST, remove the oil filter sub-assembly.

SST
09228-07501  


Hide 15601 5.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter sub-assembly installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter sub-assembly.


c.
G038462E04
2.74,0.729 2.958,0.906 true 3.021,0.854 3.333,1.021 0.313,0.167 10 true SST

Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.


d.

Using SST, tighten the oil filter sub-assembly.

SST
09228-07501  

i.

Depending on the work space available, choose from the following.

If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

Torque:
17 N*m (175 kgf*cm, 13 ft.*lbf)

If enough space is not available to use a torque wrench, tighten the oil filter sub-assembly a 3/4 turn by hand or use a common wrench.



Hide 6.ADD ENGINE OIL

a.

Clean and install the oil pan drain plug and a new gasket.

Torque:
38 N*m (382 kgf*cm, 28 ft.*lbf)


b.

Add fresh engine oil.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving", SN PLUS "resource-conserving" or SP "resource-conserving"; or ILSAC GF-6A multigrade engine oil
·

0W-20

·

5W-20

·

5W-30

·

10W-30




Standard Capacity:
Item Specified Condition
Drain and refill without oil filter sub-assembly change 5.5 liters (5.8 US qts, 4.8 Imp. qts)
Drain and refill with oil filter sub-assembly change 5.9 liters (6.2 US qts, 5.2 Imp. qts)
Dry fill 6.4 liters (6.8 US qts, 5.6 Imp. qts)



c.

Install the oil filler cap.


Hide 7.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


Hide 51457F 10.INSTALL ENGINE UNDER COVER SEAL

a.

Install the engine under cover seal with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)