Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM (w/ Differential Lock) › from 2021.06
RM27T0E _52 Drivetrain _053705 AXLE AND DIFFERENTIAL _0326415 DIFFERENTIAL SYSTEM(w/ Differential Lock) U

AXLE AND DIFFERENTIAL  DIFFERENTIAL SYSTEM(w/ Differential Lock)  DATA LIST / ACTIVE TEST  


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST OF 4 WHEEL DRIVE CONTROL ECU


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List.


f.

According to the display on the GTS, read the Data List.

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading/
Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
FL Wheel Speed Front wheel speed sensor LH reading/
Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
RR Wheel Speed Rear wheel speed sensor RH reading/
Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear wheel speed sensor LH reading/
Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
Vehicle Speed Maximum wheel speed sensor reading/
Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
Rear Differential Lock Control SW Differential lock switch status/
ON or OFF
ON: ON (LOCK)
OFF: OFF (FREE)
-
Rear Differential Lock Position SW Differential lock indicator switch status/
ON or OFF
ON: Switch on (lock)
OFF: Switch off (free)
-
IG SW Ignition switch status/
ON or OFF
ON: Ignition switch ON -
Rear Differential Lock Limit SW (RLY1) Limit switch (RLY1) status/
ON or OFF
ON: Set to free or switching between free and lock
OFF: Set to lock
-
Rear Differential Lock Limit SW (RLY2) Limit switch (RLY2) status/
ON or OFF
ON: Switching between free and lock, or set to lock
OFF: Set to free
-
Clutch SW Clutch start switch status/
ON or OFF
ON: Clutch pedal depressed
OFF: Clutch pedal released
Used only for vehicles with a manual transmission.
Displays OFF for vehicles with an automatic transmission.
Shift SW Status (N Range) Shift lever neutral condition/
ON or OFF
ON: Shift lever in N
OFF: Shift lever not in N
-
Engine Fail Signal Engine control system malfunction status/
Normal or Abnormal
Normal: Engine control system normal Abnormal: Engine control system malfunctioning
Shift SW Status (P Range) Shift lever P condition/
ON or OFF
ON: Shift lever in P
OFF: Shift lever not in P
Used only for vehicles with an automatic transmission.
Displays OFF for vehicles with a manual transmission.
Stop Light SW Stop light switch assembly condition/
ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
VSC System VSC system availability/
Without or With
Without: w/o VSC
With: w/ VSC
-
VSC Fail Signal VSC system malfunction status/
Normal or Abnormal
Normal: VSC system normal Abnormal: VSC system malfunctioning or vehicle without VSC
Rear Differential Lock Shift Motor Target Current Rear differential lock shift motor drive circuit target current value/
Min.: 0.0 A
Max.: 25.5 A
Normal: 0.0 A
Switching: 0.0 to 25.5 A
-
Motor Actual Current Motor drive circuit actual current value/
Min.: 0.0 A
Max.: 25.5 A
Normal: 0.0 A
Switching: 0.0 to 25.5 A
-
Motor Energization Status Signal Motor power signal status/
ON or OFF
ON: Power supplied to motor
OFF: Power not supplied to motor
-
C/C Cancel Request Cruise control cancellation signal status/
ON or OFF
ON: Cruise control cancellation requested
OFF: Cruise control cancellation not requested
-
L4 Position Signal L4 status signal/
ON or OFF
ON: L4 state
OFF: State other than L4
-
Rear Differential Lock Position Signal Rear differential lock condition signal/
ON or OFF
ON: Lock condition
OFF: Condition other than lock
-
Buzzer Request Buzzer sounding request/
Sound, Sound (3 times), No Sound
No Sound: Does not sound Sound (3 times): During a malfunction*1
Rear Differential Lock Indicator Request Rear differential lock indicator light request/
Blink3, Blink2, Blink1, ON or OFF
·

Blink3: Indicator light blinks

·

Blink2: Indicator light blinks 3 times

·

Blink1: Indicator light blinks

·

ON: Indicator light illuminates

·

OFF: Indicator light turns off


·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)


IG Voltage IG monitor voltage/
Min.: 0.0 V
Max.: 25.5 V
11.0 to 14.0 V: Ignition switch ON -
Motor Voltage Motor driver circuit monitor voltage/
Min.: 0.0 V
Max.: 25.5 V
Normal: 1.5 to 12.0 V
Switching: 3.5 V
-
Mode Status Mode transition condition/
Initial Control, Particular Control at Start-Up, Shift Setting Control at Start-Up, H4F, H4L, L4F, L4L, L4LL*2, H4F->H4L, H4L->H4F, L4F->L4L, L4L->L4F, H4F->L4F, L4F->H4F, H4L->L4L, L4L->H4L, L4L->L4LL*2, L4LL->L4L*2, K7, K8, S04, S05, S06, S07, S08, S09, S10, S11, S14, S15, S16, S17, S18, B1, B2, B3, B4, B6, B7, B8, B9, HF1
Transition condition of the high-low transfer actuator, center differential lock actuator and differential lock shift actuator
HINT:
·

K7 or K8: Control while switching prohibited

·

S04 to S18: Control while switching limited

·

B1 to B9: During return control

·

HF1: During fuel control



Motor Relay (RY1-1) Internal ECU relay (RY1-1) condition*3/
ON or OFF
ON: Relay on
OFF: Relay off
-
Motor Relay (RY1-2) Internal ECU relay (RY1-2) condition*3/
ON or OFF
ON: Relay on
OFF: Relay off
-
Motor Relay (RY2-1) Internal ECU relay (RY2-1) condition*3/
ON or OFF
ON: Relay on
OFF: Relay off
-
Motor Relay (RY2-2) Internal ECU relay (RY2-2) condition*3/
ON or OFF
ON: Relay on
OFF: Relay off
-
AT/MT AT or MT identification/
AT or MT
AT: Automatic transmission
MT: Manual transmission
-
CAN Signal Invalid Status by IG Voltage Low Whether CAN communication data invalid condition due to IG voltage drop/
Valid or Inval
Valid: IG voltage 10 V or higher Inval: IG voltage below 10 V
SW Input Invalid Status by IG Voltage Low Input invalid condition of switches inside actuator due to IG voltage drop/
Valid or Inval
Valid: IG voltage 7.4 V or higher Inval: IG voltage below 7.4 V
Transfer Shift Invalid Status by IG Voltage Low Transfer shift actuator switching operation invalid condition due to IG voltage drop/
Valid or Inval
Valid: IG voltage 10 V or higher Inval: IG voltage below 10 V
Number of DTC Number of DTCs stored/
Min.: 0
Max.: 255
0 -

*1: For details regarding malfunctions, refer to the buzzer sounding conditions of the diagnosis system (See page Drivetrain>AXLE AND DIFFERENTIAL>DIFFERENTIAL SYSTEM (w/ Differential Lock)>DIAGNOSIS SYSTEM).

*2: Item not equipped, therefore not displayed

*3: For the position of the relay, refer to the P17A9 wiring diagram (See page Drivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>P17A9).