Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM (w/ Differential Lock) › from 2021.06
RM27T0E _52 Drivetrain _053705 AXLE AND DIFFERENTIAL _0326415 DIFFERENTIAL SYSTEM(w/ Differential Lock) C

AXLE AND DIFFERENTIAL  DIFFERENTIAL SYSTEM(w/ Differential Lock)  P17C3  Rear Differential Lock Limit SW Circuit  


DESCRIPTION

When the differential lock shift actuator is switching between free and lock, the RLY1 and RLY2 terminals are in one of the ON/OFF combinations listed in the table below.

Terminal Mode
FREE Switching LOCK
RLY1 ON ON OFF
RLY2 OFF ON ON

A malfunction is detected depending on the combination of the 2 circuits that make up the limit switch of the differential lock shift actuator assembly.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17C3
1.

When rear differential is switching between free and lock (differential lock shift motor operating) with ignition switch turned to ON

2.

The combination of RLY1 and RLY2 does not match

3.

0 seconds

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Differential lock shift actuator



WIRING DIAGRAM

C341716E02
5.073,3.083 5.49,3.313 0.417,0.229 10 false G53 5.073,3.25 6.885,3.417 1.813,0.167 10 false 4 Wheel Drive Control ECU 5.042,0.792 5.406,0.969 0.365,0.177 10 false RLY1 5.042,1.521 5.406,1.698 0.365,0.177 10 false RLY2 4.823,1.5 4.979,1.688 0.156,0.188 10 false 1 4.813,0.76 4.948,0.948 0.135,0.188 10 false 2 3.719,0.75 3.948,0.927 0.229,0.177 10 false 6 3.708,1.5 3.938,1.677 0.229,0.177 10 false 5 0.823,1.5 1.052,1.677 0.229,0.177 10 false 4 1.865,2.031 2.74,2.229 0.875,0.198 10 false Limit Switch 1.313,2.781 1.656,2.958 0.344,0.177 10 false E1 1.302,2.969 3.208,3.198 1.906,0.229 10 false Differential Lock Shift Actuator 5.458,0.271 5.75,0.531 0.292,0.26 10 false IG 1.073,1.51 1.51,1.688 0.438,0.177 10 false GND2 3.229,0.771 3.656,0.948 0.427,0.177 10 false RLY1 3.229,1.521 3.656,1.698 0.427,0.177 10 false RLY2

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL LOCK SHIFT ACTUATOR)
a.

Disconnect the G53 4 wheel drive control ECU connector.


b.

Disconnect the E1 differential lock shift actuator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-2 (RLY1) - E1-6 (RLY1) Always Below 1 Ω
G53-1 (RLY2) - E1-5 (RLY2) Always Below 1 Ω
E1-4 (GND2) - Body ground Always Below 1 Ω
G53-2 (RLY1) or E1-6 (RLY1) - Body ground Always 10 kΩ or higher
G53-1 (RLY2) or E1-5 (RLY2) - Body ground Always 10 kΩ or higher




OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
a.

Disconnect the E1 differential lock shift actuator connector.


b.
U165697E03
1.271,1.74 1.677,1.323 true 2.354,1.74 1.927,1.354 true 1.635,0.271 1.885,0.458 0.25,0.188 10 false E1 0.135,0.073 0.385,0.323 0.25,0.25 10 false *a 1.042,1.76 1.458,1.948 0.417,0.188 10 false RLY2 2.281,1.75 2.698,1.938 0.417,0.188 10 false RLY1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E1-6 (RLY1) - Body ground Ignition switch ON 10 to 14 V
E1-5 (RLY2) - Body ground Ignition switch ON 10 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Differential Lock Shift Actuator)



OK

REPLACE DIFFERENTIAL LOCK SHIFT ACTUATOR

NG

REPLACE 4 WHEEL DRIVE CONTROL ECU