2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

DATA LIST / ACTIVE TEST

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  7. Check the values by referring to the table below.

Engine and ECT 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
The speed indicated on the speedometer.
Engine Speed
Engine speed:
Min.: 0 rpm, Max.: 16383.75 rpm
650 to 750 rpm: Idling
-
Calculate Load
Load calculated by ECM:
Min.: 0%, Max.: 100%
11.4 to 16.4%: Idling
13.1 to 18.9%: Running without load (2000 rpm)
-
Vehicle Load
Vehicle load:
Min.: 0%, Max.: 25700%
Actual vehicle load
The load percentage in terms of the maximum intake airflow amount.
MAF
Airflow rate from MAF meter:
Min.: 0 g/sec., Max.: 655.35 g/sec.
3.2 to 4.7 g/sec.: Idling
13.1 to 18.9 g/sec.: 2000 rpm
If the value is approximately 0.0 g/sec.:
  1. The mass air flow meter power source circuit is open or shorted.
  1. The VG circuit is open or shorted.
If the value is 271.0 g/sec. or more:
  1. The E2G circuit is open.
Atmospheric Pressure
Atmospheric pressure:
Min.: 0 kPa, Max.: 255 kPa
Equivalent to atmospheric pressure (absolute pressure)
-
Coolant Temp
Engine coolant temperature:
Min.: -40°C, Max.: 140°C
80 to 100°C (176 to 212°F):
After warming up
  1. If the value is -40°C (-40°F), the sensor circuit is open.
  1. If the value is 140°C (284°F) or higher, the sensor circuit is shorted.
Intake Air
Intake air temperature:
Min.: -40°C, Max.: 140°C
Equivalent to ambient air temperature
  1. If the value is -40°C (-40°F), the sensor circuit is open.
  1. If the value is 140°C (284°F) or higher, the sensor circuit is shorted.
Engine Run Time
Engine run time:
Min.: 0 s
Max.: 65535 s
Time after engine start
-
Initial Engine Coolant Temp
Initial engine coolant temperature:
Min.: -40°C, Max.: 120°C
Coolant temperature when engine started
Service data.
Initial Intake Air Temp
Initial intake air temperature:
Min.: -40°C, Max.: 120°C
Intake air temperature when engine started
Service data.
Battery Voltage
Battery voltage:
Min.: 0, Max.: 65.535 V
11 to 14 V: Idling
-
Accel Sens. No.1 Volt %
Accelerator Pedal Position (APP) No. 1:
Min.: 0%, Max.: 100%
10 to 22%: Accelerator pedal released
54 to 86%: Accelerator pedal fully depressed
-
Accel Sens. No.2 Volt %
APP No. 2:
Min.: 0%, Max.: 100%
12 to 42%: Accelerator pedal released
66 to 98%: Accelerator pedal fully depressed
-
Accel Sensor Out No.1
APP sensor No. 1 voltage:
Min.: 0 V, Max.: 4.98 V
-
-
Accel Sensor Out No.2
APP sensor No. 2 voltage:
Min.: 0 V, Max.: 4.98 V
-
-
Accel Sensor Out No.1
APP sensor No. 1 voltage:
Min.: 0 V, Max.: 5 V
0.5 to 1.1 V: Accelerator pedal released
2.6 to 4.5 V: Accelerator pedal fully depressed
-
Accel Sensor Out No.2
APP sensor No. 2 voltage:
Min.: 0 V, Max.: 5 V
1.2 to 2.0 V: Accelerator pedal released
3.4 to 5.0 V: Accelerator pedal fully depressed
-
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting idle:
ON or OFF
ON: Idling
-
Accel Fully Close #1 (AD)
Accelerator fully closed value No. 1 (AD):
Min.: 0 V, Max.: 4.98 V
-
The ETCS service data.
Accel Fully Close Learn #1
Accelerator fully closed learning value No. 1:
Min.: 0 deg., Max.: 124.512 deg.
-
The ETCS service data.
Accel Fully Close Learn #2
Accelerator fully closed learning value No. 2:
Min.: 0 deg., Max.: 124.512 deg.
-
The ETCS service data.
Throttle Sensor Volt %
Absolute throttle position sensor:
Min.: 0%, Max.: 100%
  1. 10 to 22%: Throttle fully closed
  2. 64 to 96%: Throttle fully open
Read the value with the non-intrusive operation (Active Test).
Throttl Sensor #2 Volt %
Absolute throttle sensor positioning #2:
Min.: 0%, Max.: 100%
-
The calculated value based on VTA2.
ST1
Brake pedal signal:
ON or OFF
ON: Brake pedal released
-
System Guard
System guard:
ON or OFF
-
-
Open Side Malfunction
Open side malfunction:
ON or OFF
-
-
Throttle Idle Position
Whether or not throttle position sensor detecting idle:
ON or OFF
ON: Idling
-
Throttle Require Position
Throttle requirement position:
Min.: 0 V, Max.: 5 V
0.5 to 1.1 V: Idling
-
Throttle Sensor Position*2
Throttle sensor positioning:
Min.: 0%, Max.: 100%
0%: Accelerator pedal released
50 to 80%: Accelerator pedal fully depressed
Recognition value for throttle opening angle on ECM..
Throttle Position No.1
Throttle position sensor No. 1 output voltage:
Min.: 0 V, Max.: 4.98 V
-
-
Throttle Position No.2
Throttle position sensor No. 2 output voltage:
Min.: 0 V, Max.: 4.98 V
-
-
Throttle Position No.1
Throttle position No. 1:
Min.: 0 V, Max.: 5 V
0.5 to 1.1 V: Throttle fully closed
3.2 to 4.8 V: Throttle fully open
-
Throttle Position No.2
Throttle position No. 2:
Min.: 0 V, Max.: 5 V
2.1 to 3.1V: Throttle fully closed
4.6 to 5.0 V: Throttle fully open
-
Throttle Position Command
Throttle position command value:
Min.: 0 V, Max.: 4.9804 V
0.5 to 4.8 V
The ETCS service data.
Throttle Sens Open Pos #1
Throttle sensor opener position No. 1:
Min.: 0 V, Max.: 4.9804 V
0.6 to 1.4 V
The ETCS service data.
Throttle Sens Open Pos #2
Throttle sensor opener position No. 2:
Min.: 0 V, Max.: 4.9804 V
1.7 to 2.5 V
The ETCS service data.
Throttle Sens Open #1 (AD)
Throttle sensor opener position No. 1 (AD):
Min.: 0 V, Max.: 4.98 V
0.5 to 4.8 V
The ETCS service data.
Throttle Motor
Whether or not throttle actuator control permitted:
ON or OFF
ON: Ignition switch ON.
OFF: ETCS has failed
-
Throttle Motor Current
Throttle actuator current:
Min.: 0 A, Max.: 20 A
0 to 3.0 A: Idling
The ETCS service data.
Throttle Motor DUTY
Throttle actuator:
Min.: 0%, Max.: 100%
10 to 22%: Idling after engine warmed up
The ETCS service data.
Throttle Motor Open Duty
Throttle actuator opening duty ratio:
Min.: 0%, Max.: 100%
0 to 40%: Idling
The ETCS service data.
Throttle Motor Close Duty
Throttle actuator closed duty ratio:
Min.: 0%, Max.: 100%
0 to 40%: Idling
The ETCS service data.
Throttle Motor Duty (Open)
Throttle actuator duty ratio (open):
Min.: 0%, Max.: 100%
-
-
Throttle Motor Duty (Close)
Throttle actuator duty ratio (close):
Min.: 0%, Max.: 100%
-
-
Throttle Fully Closed Learn
Throttle valve fully closed
(learned value):
Min.: 0 V, Max.: 5 V
0.4 to 1.0 V (Accelerator pedal released)
-
ETCS Actuator Power
Whether or not electric throttle control system power input:
ON or OFF
ON: Ignition switch ON and system normal
OFF: ETCS has failed
-
+BM Voltage
+BM voltage:
Min.: 0, Max.: 19.922
11 to 14: Ignition switch ON and system normal
-
Actuator Power Supply
Actuator power supply:
ON or OFF
ON: Idling
-
Clutch Current
Clutch current:
Min.: 0 A, Max.: 2.49 A
-
-
Fail Safe Drive
Whether or not fail-safe function executed:
ON or OFF
ON: ETCS has failed
OFF: ETCS normal
The ETCS service data.
Fail Safe Drive (Main CPU)
Whether or not fail-safe function executed:
ON or OFF
ON: ETCS has failed
OFF: ETCS normal
The ETCS service data.
Injector (Port)
Injection period of No. 1 cylinder:
Min.: 0 ms, Max.: 32.64 ms
1.6 to 2.4 msec.: Idling
-
Injection Volum (Cylinder 1)
Injection volume (Cylinder 1):
Min.: 0 ml, Max.: 2.048 ml
0.005 to 0.015 ml: Idling
The quantity of fuel injection volume for 10 times.
Fuel Pump/Speed Status
Fuel pump/status:
ON or OFF
-
Active Test support data.
EVAP (Purge) VSV
EVAP (Purge) VSV control duty:
Min.: 0%, Max.: 100%
0 to 100%: Idling
The order signal from the ECM.
Evap Purge Flow
Purge flow:
Min.: 0%, Max.: 102.4%
0 to 100%: Idling
Service data.
Purge Destiny Learn Value
Learning value of purge density:
Min.: -50, Max.: 350
-35 to 1: Idling
Service data.
EVAP Purge VSV
VSV status for EVAP control:
ON or OFF
-
-
Target Air-Fuel Ratio
Air fuel ratio:
Min.: 0, Max.: 1.999
0.8 to 1.2: Idling
-
AF Lambda B1S1
Short-term fuel trim associated with bank 1 sensor 1:
Min.: 0, Max.: 1.999
Value less than 1 (0.000 to 0.999) = Rich
Stoichiometric air fuel ratio = 1
Value more than 1 (1.001 to 1.999) = Lean
-
AF Lambda B2S1
Short-term fuel trim associated with bank 2 sensor 1:
Min.: 0, Max.: 1.999
Value less than 1 (0.000 to 0.999) = Rich
Stoichiometric air fuel ratio = 1
Value more than 1 (1.001 to 1.999) = Lean
-
AFS Voltage B1S1
A/F sensor output voltage bank 1 sensor 1:
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Voltage B2S1
A/F sensor output voltage bank 2 sensor 1:
Min.: 0 V, Max.: 7.999 V
2.8 to 3.8 V: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Current B1S1
A/F sensor output current bank 1 sensor 1:
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Current B2S1
A/F sensor output current bank 2 sensor 1:
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2S B1S2
Heated oxygen sensor output voltage bank 1 sensor 2:
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2S B2S2
Heated oxygen sensor output voltage bank 2 sensor 2:
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
Short FT #1
Short-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
-20 to 20%
Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
Long FT #1
Long-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
-30 to 30%
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #1
Total fuel trim of bank 1:
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling
-
Short FT #2
Short-term fuel trim of bank 2:
Min.: -100%, Max.: 99.2%
-20 to 20%
Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric air fuel ratio.
Long FT #2
Long-term fuel trim of bank 2:
Min.: -100%, Max.: 99.2%
-30 to 30%
Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #2
Total fuel trim of bank 2:
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling
-
Fuel System Status #1
Fuel system status (bank 1):
OL or CL or OLDrive or OLFault or CLFault
CL: Idling after warming up
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (bank 2):
OL or CL or OLDrive or OLFault or CLFault
CL: Idling after warming up
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
IGN Advance
Ignition timing advance for No. 1 cylinder:
Min.: -64 deg., Max.: 63.5 deg.
BTDC 7 to 24°: Idling
-
Knock Feedback Value
Feedback value of knocking:
Min: -64°CA, Max.: 1984°CA
-22 to 0°CA:
Driving at 70 km/h (44 mph)
Service data.
Knock Correct Learn Value
Correction learning value of knocking:
Min: -64°CA, Max.: 1984°CA
0 to 22°CA:
Driving at 70 km/h (44 mph)
Service data.
ACIS VSV
VSV status for ACIS control:
ON or OFF
-
-
VVT Control Status #2
VVT control (bank 2) status:
ON or OFF
-
-
VVT Control Status #1
VVT control (bank 2) status:
ON or OFF
-
-
VVT Aim Angle #1*1
VVT aim angle (bank 1):
Min.: 0%, Max.: 100%
0 to 100%: Idling
The VVT duty signal value during the intrusive operation.
VVT Change Angle #1*1
VVT change angle (bank 1):
Min.: 0°FR, Max.: 60°FR
0 to 56°FR: Idling
The displacement angle during the intrusive operation.
VVT OCV Duty #1*1
VVT OCV operation duty (bank 1):
Min.: 0%, Max.: 100%
0 to 100%: Idling
The requested duty value for the intrusive operation.
VVT Aim Angle #2*1
VVT aim angle (bank 2):
Min.: 0%, Max.: 100%
0 to 100%: Idling
The VVT duty signal value during the intrusive operation.
VVT Aim Angle #2*1
VVT change angle (bank 2):
Min.: 0°FR, Max.: 60°FR
0 to 56°FR: Idling
The displacement angle during the intrusive operation.
VVT OCV Duty #2*1
VVT OCV operation duty (bank 2):
Min.: 0%, Max.: 100%
0 to 100%: Idling
The requested duty value for the intrusive operation.
Catalyst Temp B1S1
Catalyst temperature (bank 1 sensor 1):
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B2S1
Catalyst temperature (bank 2 sensor 1):
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B1S2
Catalyst temperature (bank 1 sensor 2):
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B2S2
Catalyst temperature (bank 2 sensor 2):
Min.: -40°C, Max.: 6513.5°C
-
-
Starter Signal
Starter signal:
ON or OFF
ON: Cranking
-
Starter Control
Starter switch status:
ON or OFF
ON: Cranking
-
Power Steering Signal Record
Power steering switch:
ON or OFF
ON: Power steering operation
-
Starter Relay
Starter relay status:
ON or OFF
ON: Cranking
-
Power Steer. Sig. Record
Power steering signal (history):
ON or OFF
ON: When steering wheel first turned after battery terminals connected
This signal status is usually on until the cables are disconnected from the battery terminals.
ACC Relay
ACC relay status:
ON or OFF
ON: Cranking
-
Neutral Position SW Signal
PNP switch status
ON or OFF
ON: P or N position
-
Stop Light Switch
Stop light switch status:
ON or OFF
ON: Brake pedal depressed
-
A/C Signal
A/C switch status:
ON or OFF
ON: A/C ON
-
Closed Throttle Position SW
Closed throttle position switch:
ON or OFF
ON: Throttle fully closed
OFF: Throttle open
-
Fuel Cut Condition
Fuel cut condition:
ON or OFF
ON: Fuel cut operating
-
Immobiliser Communication
Immobiliser communication:
ON or OFF
ON: Normal
-
Electrical Load Signal
Electrical load signal:
ON or OFF
ON: Headlights or defogger turned on
-
Check Mode
Check mode:
ON or OFF
ON: Check mode on
(Click here)
SPD Test Result
Check mode result for vehicle speed sensor:
Compl or Incmpl
-
-
Misfire Test Result
Check mode result for misfire monitor:
0: COMPL, 1: INCMPL
-
-
OXS1 Test Result
Check mode result for HO2 sensor (bank 1):
Compl or Incmpl
-
-
OXS2 Test Result
Check mode result for HO2 sensor (bank 2):
Compl or Incmpl
-
-
A/F Test Results #2
Check mode result for air fuel ratio sensor (bank 2):
Compl or Incmpl
-
-
A/F Test Results #1
Check mode result for air fuel ratio sensor (bank 1):
Compl or Incmpl
-
-
Complete Parts Monitor
Comprehensive component monitor:
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor:
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor:
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor:
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor:
Compl or Incmpl
-
-
O2S (A/FS) Heater Monitor
O2S (A/FS) heater monitor:
Not Avl or Avail
-
-
O2S (A/FS) Heater Monitor
O2S (A/FS) heater monitor:
Compl or Incmpl
-
-
O2S (A/FS) Monitor
O2S (A/FS) monitor:
Not Avl or Avail
-
-
O2S (A/FS) Monitor
O2S (A/FS) monitor:
Compl or Incmpl
-
-
A/C Monitor
A/C monitor:
Not Avl or Avail
-
-
A/C Monitor
A/C monitor:
Compl or Incmpl
-
-
2nd Air Monitor
2nd Air monitor:
Not Avl or Avail
-
-
2nd Air Monitor
2nd Air monitor:
Compl or Incmpl
-
-
EVAP Monitor
EVAP monitor:
Not Avl or Avail
-
-
EVAP Monitor
EVAP monitor:
Compl or Incmpl
-
-
Heated Catalyst Monitor
Heated catalyst monitor:
Not Avl or Avail


Heated Catalyst Monitor
Heated catalyst monitor:
Compl or Incmpl


Catalyst Monitor
Catalyst monitor:
Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor:
Compl or Incmpl
-
-
Component Monitor ENA
Comprehensive component monitor:
Unable or Enable
-
-
# Codes (Include History)
Number of emission related DTCs
0: No emission related DTC stored
-
MIL
MIL status:
ON or OFF
ON: MIL on
-
MIL ON Run Distance
MIL on run distance:
Min.: 0 km
Max.: 65535 km
Distance after DTC stored
-
Running Time from MIL ON
Running time from MIL on:
Min.: 0 min.
Max.: 65535 min.
Equivalent to running time after MIL on
-
Time after DTC Cleared
Time after DTC cleared:
Min.: 0 min.
Max.: 65535 min.
Equivalent to time after DTCs cleared
-
Distance from DTC Cleared
Distance after DTC cleared:
Min.: 0 km, Max.: 65535 km
Equivalent to drive distance after DTCs cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared:
Min.: 0, Max.: 255
-
The number of warm-up cycles after the DTC(s) are cleared.
OBD Requirements
OBD requirement
OBD2
-
Number of Emission DTC
Emission related DTCs
-
The number of emission related DTCs.
TC and TE1
TC and CG (TE1) terminals of DLC3:
ON or OFF
-
Active Test support data.
Ignition Trig. Count
Ignition counter:
Min.: 0, Max.: 600
0 to 600
-
Cylinder #1 to 6 Misfire Count
Misfire count of cylinder 1 to 6:
Min.: 0, Max.: 255
0
This item displayed only when idling.
All Cylinders Misfire Count
All cylinders misfire count:
Min.: 0, Max.: 255
0 to 35
-
Misfire RPM
Engine speed for first misfire range:
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Misfire 0
-
Misfire Load
Engine load for first misfire range:
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: Misfire 0
-
Misfire Margin
Misfire monitoring:
Min.: -100%, Max.: 99.22%
-100 to 99.22%
Misfire detecting margin.
ACT VSV
A/C cut status for Active Test:
ON or OFF
-
Active Test support data.
Idle Fuel Cut
Fuel cut idle:
ON or OFF
ON: Fuel cut operating
Idle Fuel Cut is "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
FC TAU
Fuel cut TAU (Fuel cut during very light load):
ON or OFF
ON: Fuel cut operating
Fuel cut is being performed under a very light load to prevent the engine combustion from becoming incomplete.
Model Code
Model code
-
The identifying model code:
GRJ2#
Engine Type
Engine type
-
The identifying engine type:
1GRFE
Cylinder Number
Cylinder number:
Min.: 0, Max.: 255
-
The identifying cylinder number:
6
Transmission Type
Transmission type
-
The identifying transmission type:
5AT
Destination
Destination
-
The identifying destination:
W
Model Year
Model year:
Min.: 1900, Max.: 2155
-
The identifying model year:
200#
System Identification
System identification
-
The identifying engine system:
Gasoline (gasoline engine)
Engine Speed of Cyl #1
Engine speed for cylinder 1:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #2
Engine speed for cylinder 2:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #3
Engine speed for cylinder 3:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #4
Engine speed for cylinder 4:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #5
Engine speed for cylinder 5:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #6
Engine speed for cylinder 6:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Av Engine Speed of All Cyl
Engine speed for all cylinders:
Min.: 0 rpm, Max.: 25600 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.

HINT:
  1. Normal Condition: If no idling conditions are specified, the shift lever should be in N or P, and the A/C switch and all accessory switches should be off.
  2. *1: Data List values are only displayed when performing the following Active Tests: Control the VVT Linear (Bank1), Control the VVT Linear (Bank2), Control the VVT Exhaust Linear (Bank1) and Control the VVT Exhaust Linear (Bank2). For other Active Tests, the Data List value will be 0.
  3. *2: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).


ACTIVE TEST

HINT:
Using the intelligent tester to perform the Active Tests allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the tester on.

  4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  5. According to the display on the tester, perform the "Active Test".

Engine and ECT 
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Injection Volume
Change injection volume
-12.5 to 24.8%
  1. All the injectors are tested at the same time.
  2. Perform the test at less than 3000 rpm.
  3. The injection volume can be changed in 1% graduations within the control range.
Control the Injection Volume for A/F Sensor
Change injection volume
Lower by 12.5% or increase by 24.8%
  1. Perform the test at less than 3000 rpm.
  2. Control the Injection Volume for A/F Sensor enables the checking and graphing of the A/F (Air Fuel ratio) sensor and Heated Oxygen (HO2) sensor voltage outputs.
  3. To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F Control System / AFS Voltage B1S1 and O2S B1S2.
Activate the VSV for Intake Control
Activate VSV for intake control
ON/OFF
-
Activate the VSV for Evap Control
Activate purge VSV control
ON/OFF
-
Control the A/C Cut Signal
Control the A/C cut signal
ON/OFF
-
Control the Fuel Pump / Speed
Activate fuel pump (C/OPN Relay)
ON/OFF
The test is possible when the following conditions are met:
  1. The ignition switch is ON.
  2. The engine is stopped.
Connect the TC and TE1
Turn on and off TC and CG (TE1) connection
ON/OFF
  1. ON: TC and TE1 are connected.
  1. OFF: TC and TE1 are disconnected.
Control the Idle Fuel Cut Prohibit
Prohibit idling fuel cut control
ON/OFF
The idling fuel-cut is turned on when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
Activate the Starter Relay
Activate starter relay
ON/OFF
-
Activate the ACC Cut Relay
Activate ACC cut relay
ON/OFF
The test is possible when the following conditions are met:
  1. The ignition switch is ON.
  2. The engine is stopped.
Control the ETCS Open/Close Slow Speed
Throttle actuator
Close/Open
The test is possible when the following conditions are met:
  1. The ignition switch is ON.
  2. The engine is stopped.
  3. The accelerator pedal is fully depressed (APP: 58 degrees or more).
Control the ETCS Open/Close Fast Speed
Throttle actuator
Close/Open
Control the VVT Linear (Bank1)
Control VVT (bank 1)
Between -128 and 127%
  1. The engine stalls or idles roughly when the VVT actuator is operated by 100%.
  2. The test is possible during idle.
Control the VVT System (Bank1)
Turn on and off OCV
(Oil Control Valve)
ON/OFF
  1. The engine stalls or idles roughly when the OCV is turned on.
  2. The engine runs or idles normally when the OCV is off.
Control the VVT Linear (Bank2)
Control VVT (bank 2)
Between -128 and 127%
  1. The engine stalls or idles roughly when the VVT actuator is operated by 100%.
  2. The test is possible during idle.
Control the VVT System (Bank2)
Turn on and off OCV
(Oil Control Valve)
ON/OFF
  1. The engine stalls or idles roughly when the OCV is turned on.
  2. The engine runs or idles normally when the OCV is off.
Control the Cylinder #1 Fuel Cut
No. 1 cylinder injector fuel cut
ON/OFF
The test is possible while the vehicle is stopped and the engine is idling.
Control the Cylinder #2 Fuel Cut
No. 2 cylinder injector fuel cut
ON/OFF
Control the Cylinder #3 Fuel Cut
No. 3 cylinder injector fuel cut
ON/OFF
Control the Cylinder #4 Fuel Cut
No. 4 cylinder injector fuel cut
ON/OFF
Control the Cylinder #5 Fuel Cut
No. 5 cylinder injector fuel cut
ON/OFF
Control the Cylinder #6 Fuel Cut
No. 6 cylinder injector fuel cut
ON/OFF
Control the All Cylinder Fuel Cut
All cylinder fuel cut
ON/OFF
Check the Cylinder Compression*
Check the cylinder compression pressure
ON/OFF
The fuel injection and ignition stop in all the cylinders.

HINT:
*: When cranking the engine, the Active Test measures the speed of each cylinder.
In this Active Test, the fuel of all cylinders is cut, and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is higher than the other cylinders, the compression pressure of that cylinder is determined to be lower than the other cylinders.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON and turn the tester on.
  5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

    HINT:
    If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine and ECT / Data List / Compression / Engine Speed of Cyl #1, Engine Speed of Cyl #2, Engine Speed of Cyl #3, Engine Speed of Cyl #4, Engine Speed of Cyl #5, Engine Speed of Cyl #6 and Av Engine Speed of All Cyl.

  6. While the engine is not running, press the RIGHT or LEFT button to change the Check the Cylinder Compression to on.

    HINT:
    After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited, and each cylinder engine speed measurement will enter standby mode.

  7. Crank the engine for about 10 seconds.
  8. Monitor the engine speed (Engine Speed of Cyl #1 to #6, Av Engine Speed of All Cyl) displayed on the tester.

    HINT:
    At first, the tester display will show each cylinder engine speed measurement to be extremely high. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

    NOTICE:
    1. After the Check the Cylinder Compression is turned on, it will automatically turn off after 255 seconds.
    2. When the Check the Cylinder Compression test is off and the engine is cranked, the engine will start.
    3. If the Check the Cylinder Compression test needs to be performed after it is turned on and performed once, press EXIT to return to the Active Test menu screen. Then perform the Check the Cylinder Compression test again.
    4. Use a fully-charged battery.

← FAIL-SAFE CHART (from Jan 2012)DATA LIST / ACTIVE TEST (from Jan 2012) →