DATA LIST / ACTIVE TEST
System information · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
Speed indicated on the speedometer.
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
650 to 750 rpm: Idling
-
Calculate Load
Load calculated by ECM/
Min.: 0%, Max.: 100%
- 10 to 16.4%: Idling
- 10 to 18.9%: Driving without load (2500 rpm)
-
Vehicle Load
Vehicle load/
Min.: 0%, Max.: 25700%
Actual vehicle load
-
MAF
Airflow rate from mass air flow meter/
Min.: 0 gm/s, Max.: 655.35 gm/s
2.5 to 4.7 gm/s: Idling
18.3 to 25.8 gm/s: 3000 rpm (without load)
If the value is approximately 0.0 gm/s: - The mass air flow meter power source circuit is open or shorted.
- The VG circuit is open or shorted.
- The E2G circuit is open.
Atmosphere Pressure
Atmospheric pressure/
Min.: 0 kPa, Max.: 255 kPa
Equivalent to atmospheric pressure (absolute pressure)
-
Coolant Temp
Engine coolant temperature/
Min.: -40°C, Max.: 140°C
80 to 100°C (176 to 212°F): After warming up
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F), the sensor circuit is shorted.
Intake Air
Intake air temperature/
Min.: -40°C, Max.: 140°C
Equivalent to ambient air temperature
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F), the sensor circuit is shorted.
Engine Run Time
Engine run time/
Min.: 0 s, Max.: 65535 s
Time after engine start
Service data.
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C, Max.: 119.3°C
Close to ambient air temperature
Service data.
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C, Max.: 119.3°C
Close to ambient air temperature
Service data.
Battery Voltage
Battery voltage/
Min.: 0 V, Max.: 65.535 V
11 to 14 V: Idling
-
Glow Indicator Supported
Status of glow indicator supported/
Unsupp or Supp
-
-
Glow Indicator
Glow indicator/
ON or OFF
-
-
Accelerator Position
Accelerator pedal position/
Min.: 0%, Max.: 399.9%
Actual accelerator pedal position
-
Accel Sens. No.1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1/
Min.: 0%, Max.: 100%
- 10 to 22%: Accelerator pedal released
- 52 to 90%: Accelerator pedal fully depressed
-
Accel Sens. No.2 Volt %
Absolute APP No. 2/
Min.: 0%, Max.: 100%
- 24 to 40%: Accelerator pedal released
- 68 to 99%: Accelerator pedal fully depressed
-
Accel Sensor Out No.1
APP sensor No. 1 voltage/
Min.: 0 V, Max.: 4.98 V
- 0.5 to 1.1 V: Accelerator pedal released
- 2.6 to 4.5 V: Accelerator pedal fully depressed
-
Accel Sensor Out No.2
APP sensor No. 2 voltage/
Min.: 0 V, Max.: 4.98 V
- 1.2 to 2.0 V: Accelerator pedal released
- 3.4 to 4.98 V: Accelerator pedal fully depressed
-
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting idle/
ON or OFF
ON: Idling
-
Accel Fully Close Learn #1
Accelerator pedal fully released learned value No. 1/
Min.: 0 deg, Max.: 124.5 deg
-
ETCS service data.
Accel Fully Close Learn #2
Accelerator pedal fully released learned value No. 2/
Min.: 0 deg, Max.: 124.5 deg
-
ETCS service data.
Throttle Sensor Volt %
Absolute throttle position sensor/
Min.: 0%, Max.: 100%
- 10 to 22%: Throttle fully closed
- 64 to 96%: Throttle fully open
The calculated value based on VTA1.
Throttl Sensor #2 Volt %
Throttle position sensor #2/
Min.: 0%, Max.: 100%
- 42 to 62%: Throttle fully closed
- 92 to 100%: Throttle fully open
The calculated value based on VTA2.
ST1
Brake pedal signal/
ON or OFF
ON: Brake pedal depressed
-
System Guard
System guard/
ON or OFF
-
ETCS service data.
Open Side Malfunction
Open side malfunction/
ON or OFF
-
ETCS service data.
Throttle Idle Position
Whether or not throttle position sensor detecting idle/
ON or OFF
- ON: Accelerator pedal released
- OFF: Accelerator pedal depressed
-
Throttle Require Position
Required throttle position/
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Idling
-
Throttle Sensor Position*
Throttle sensor position/
Min.: 0%, Max.: 100%
- 0%: Throttle fully closed
- 50 to 80%: Throttle fully open
Recognition value of the throttle opening angle in the ECM.
Throttle Position No. 1
Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.98 V
- 0.5 to 1.1 V: Accelerator pedal released
- 3.2 to 4.8 V: Accelerator pedal fully depressed
- 0.6 to 1.4 V: Fail-safe operating
-
Throttle Position No. 2
Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.98 V
- 2.1 to 3.1 V: Accelerator pedal released
- 4.6 to 5.0 V: Accelerator pedal fully depressed
- 2.1 to 3.1 V: Fail-safe operating
-
Throttle Position Command
Throttle position command value/
Min.: 0 V, Max.: 4.98 V
0.5 to 4.8 V
-
Throttle Sens Open Pos #1
Throttle position sensor No. 1/
Min.: 0 V, Max.: 4.98 V
0.6 to 1.4 V
ETCS service data.
Throttle Sens Open Pos #2
Throttle position sensor No. 2/
Min.: 0 V, Max.: 4.98 V
1.7 to 2.5 V
ETCS service data.
Throttle Motor Current
Throttle actuator current/
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling
ETCS service data.
Throttle Motor DUTY
Throttle actuator/
Min.: 0%, Max.: 100%
0.5 to 40%: Idling
ETCS service data.
Throttle Motor Duty (Open)
Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
ETCS service data.
Throttle Motor Duty (Close)
Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
ETCS service data.
Throttle Fully Close Learn
Throttle valve fully closed (learned value)/
Min.: 0 V, Max.: 4.98 V
0.4 to 1.0 V: Accelerator pedal released
-
+BM Voltage
+BM voltage/
Min.: 0 V, Max.: 79.998 V
11 to 14 V: Ignition switch ON and system normal
ETCS service data.
Actuator Power Supply
Actuator power supply/
ON or OFF
ON: Idling
ETCS service data.
Throttle Position
Throttle valve opening angle/
Min.: 0 deg, Max.: 499.99 deg
-
For use when engine stall, starting problems or rough idle is present.
ISC Flow
Flow rate calculated using information from each sensor/
Min.: 0 L/s, Max.: 79.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
ISC Position
Requested opening amount calculated using ISC control/
Min.: 0 deg, Max.: 499.99 deg
-
For use when engine stall, starting problems or rough idle is present.
ISC Feedback Value
ISC feedback compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
ISC Learning Value
ISC learned compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val
Compensation flow rate according to electrical load/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val
Compensation flow rate according to air conditioner load/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
PS Feedback Val
Compensation flow rate according to power steering load/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Low Revolution Control
Low engine speed control operation state/
ON or OFF
-
For use when engine stall, starting problems or rough idle is present.
N Range Status
Shift lever N status/
ON or OFF
-
For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow
Intake air compensation flow rate/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Deposit Loss Flow
Flow loss due to deposits/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Fuel Pump Duty
Fuel pump duty/
Min.: 0%, Max.: 399.9%
-
-
Injector (Port)
Injection period of No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs
1600 to 2400 μs: Idling
-
Injection Volum (Cylinder 1)
Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
0 to 0.5 ml
Fuel injection volume of 10 injections.
Current Fuel Type
Status of the current fuel type
Gasoline/petrol
-
EVAP (Purge) VSV
Purge VSV control duty/
Min.: 0%, Max.: 100%
0 to 100%: During idling
Command signal from the ECM.
Evap Purge Flow
Purge flow/
Min.: 0%, Max.: 399.9%
0 to 100%: Idling
-
Purge Density Learn Value
Purge density learned value/
Min.: -200, Max.: 199.993
Idling: -40 to 0
Service data.
EVAP Purge VSV
VSV status for EVAP control/
ON or OFF
-
-
Purge Cut VSV Duty
Purge cut VSV duty/
Min.: 0%, Max.: 399.9%
-
-
Target Air-Fuel Ratio
Target air fuel ratio/
Min.: 0, Max.: 1.99
0.8 to 1.2: During idling
-
AF Lambda B1S1
Output air fuel ratio associated with bank 1 sensor 1/
Min.: 0, Max.: 1.99
- Value less than 1 (0.000 to 0.999) = Rich
- 1 = Stoichiometric air fuel ratio
- Value more than 1 (1.001 to 1.999) = Lean
-
AF Lambda B2S1
Output air fuel ratio associated with bank 2 sensor 1/
Min.: 0, Max.: 1.99
- Value less than 1 (0.000 to 0.999) = Rich
- 1 = Stoichiometric air fuel ratio
- Value more than 1 (1.001 to 1.999) = Lean
-
AFS Voltage B1S1
Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/
Min.: 0 V, Max.: 7.99 V
2.8 to 3.8 V: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Voltage B2S1
Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/
Min.: 0 V, Max.: 7.99 V
2.8 to 3.8 V: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
AFS Current B1S1
Air fuel ratio sensor current (for Bank 1 Sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
AFS Current B2S1
Air fuel ratio sensor current (for Bank 2 Sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
A/F Heater Duty #1
Air fuel ratio sensor heater duty ratio (for Bank 1)/
Min.: 0%, Max.: 399.9%
0 to 100%
-
A/F Heater Duty #2
Air fuel ratio sensor heater duty ratio (for Bank 2)/
Min.: 0%, Max.: 399.9%
0 to 100%
-
O2S B1S2
Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2S B2S2
Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Driving at 70 km/h (44 mph)
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2 Heater B1S2
Heated oxygen sensor heater (for Bank 1 Sensor 2)/
Active or Not Act
-
-
O2 Heater B2S2
Heated oxygen sensor heater (for Bank 2 Sensor 2)/
Active or Not Act
-
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current (for Bank 1 Sensor 2)/
Min.: 0 A, Max.: 4.9 A
-
-
O2 Heater Curr Val B2S2
Heated oxygen sensor current (for Bank 2 Sensor 2)/
Min.: 0 A, Max.: 4.9 A
-
-
Short FT #1
Short-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
-20 to +20%
This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
Long FT #1
Long-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
-20 to +20%
- This item refers to the overall fuel compensation carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
- Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range. [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.
A/F Learn Value Idle #1
Air-fuel ratio learned value for idling (bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20%
Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
A/F Learn Value Low #1
Air-fuel ratio learned value for low engine loads (bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20%
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid1 #1
Air-fuel ratio learned value for mid-sized engine loads 1 (bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20%
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid2 #1
Air-fuel ratio learned value for mid-sized engine loads 2 (bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20%
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value High #1
Air-fuel ratio learned value for high engine loads (bank 1)/
Min.: -50%, Max.: 49.6%
-20 to +20%
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
Total FT #1
Total fuel trim of bank 1/
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling
-
Short FT #2
Short-term fuel trim of bank 2/
Min.: -100%, Max.: 99.2%
-20 to +20%
This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
Long FT #2
Long-term fuel trim of bank 2/
Min.: -100%, Max.: 99.2%
-20 to +20%
- This item refers to the overall fuel compensation carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
- Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #2" indicates the learned value for the current operating range. [A/F Learn Value Idle #2], [A/F Learn Value Low #2], [A/F Learn Value Mid1 #2], [A/F Learn Value Mid2 #2] and [A/F Learn Value High #2] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #2" indicates the current engine operating range.
A/F Learn Value Idle #2
Air-fuel ratio learned value for idling (bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20%
Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
A/F Learn Value Low #2
Air-fuel ratio learned value for low engine loads (bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20%
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid1 #2
Air-fuel ratio learned value for mid-sized engine loads 1 (bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20%
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid2 #2
Air-fuel ratio learned value for mid-sized engine loads 2 (bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20%
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value High #2
Air-fuel ratio learned value for high engine loads (bank 2)/
Min.: -50%, Max.: 49.6%
-20 to +20%
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
Total FT #2
Total fuel trim of bank 2/
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling
-
Fuel System Status #1
Fuel system status (Bank 1)/
OL, CL, OL Drive, OL Fault or CL Fault
CL: Idling after warming up
- OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
- CL (Closed Loop): Feedback for fuel control.
- OL Drive: Open loop due to driving conditions (fuel enrichment).
- OL Fault: Open loop due to a detected system fault.
- CL Fault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (Bank 2)/
OL, CL, OL Drive, OL Fault or CL Fault
CL: Idling after warming up
- OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
- CL (Closed Loop): Feedback for fuel control.
- OL Drive: Open loop due to driving conditions (fuel enrichment).
- OL Fault: Open loop due to a detected system fault.
- CL Fault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
Air Pump Pressure (Absolute)
Air pump pressure (absolute) (for Bank 1)/
Min.: 0 kPa, Max.: 65535 kPa
Atmospheric pressure +1 kPa or more: Air pump on, emission control valve open
Close to atmospheric pressure: Air pump off, emission control closed
Refer to DTC P2431
(Click here).
Air Pump2 Pressure (Absolute)
Air pump pressure (absolute) (for Bank 2)/
Min.: 0 kPa, Max.: 65535 kPa
Atmospheric pressure +1 kPa or more: Air pump on, emission control valve open
Close to atmospheric pressure: Air pump off, emission control valve closed
Refer to DTC P2431
(Click here).
Air Pump Pulsation Pressure
Air pump pulsation pressure/
Min.: 0 kPa, Max.: 655.35 kPa
-
Cumulative pulsation pressure calculated by ECM
(Click here).
Secondary Air Control VSV
Secondary air control VSV status/
ON or OFF
ON: Secondary air control VSV operating
-
2nd Air System Status
Secondary air system status/
ON or OFF
ON: Secondary air injection system operating
-
AI Test
AI operation prohibition/
READY or NOT RDY
READY
-
Subfreezing Conditions
Subfreezing conditions status/
ON or OFF
-
-
Air Pump Heater
Air pump heater status/
ON or OFF
-
Active Test support data.
IGN Advance
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg, Max.: 63.5 deg
BTDC 7 to 24 deg: Idling
-
Knock Feedback Value
Knocking feedback value/
Min.: -1024°CA, Max.: 1023.9°CA
-3°CA:
Driving at 70 km/h (44 mph)
Service data.
Knock Correct Learn Value
Knocking correction learned value/
Min.: -1024°CA, Max.: 1023.9°CA
5 to 28°CA:
Driving at 70 km/h (44 mph)
Service data.
Idle Spark Advn Ctrl #1
Individual cylinder timing advance compensation amount (No. 1)/
Min.: 0°CA, Max.: 15.93°CA
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2
Individual cylinder timing advance compensation amount (No. 2)/
Min.: 0°CA, Max.: 15.93°CA
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3
Individual cylinder timing advance compensation amount (No. 3)/
Min.: 0°CA, Max.: 15.93°CA
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 4)/
Min.: 0°CA, Max.: 15.93°CA
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #5
Individual cylinder timing advance compensation amount (No. 5)/
Min.: 0°CA, Max.: 15.93°CA
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #6
Individual cylinder timing advance compensation amount (No. 6)/
Min.: 0°CA, Max.: 15.93°CA
-
For use when engine stall, starting problems or rough idle is present.
VVT Control Status #1
Variable valve timing (VVT) control status (Bank 1)/
ON or OFF
-
-
VVT Control Status #2
VVT control status (Bank 2)/
ON or OFF
-
-
VVT Advance Fail
VVT control failure status/
ON or OFF
ON: VVT control failure
-
VVT Aim Angle #1
VVT target duty (Bank 1)/
Min.: 0%, Max.: 399.9%
-
VVT duty signal value during forced operation.
VVT Change Angle #1
VVT displacement angle (Bank 1)/
Min.: 0 DegFR, Max.: 639.9 DegFR
-
Displacement angle during forced operation.
VVT OCV Duty #1
Camshaft timing oil control valve operation duty (for Intake Side of Bank 1)/
Min.: 0%, Max.: 399.9%
-
Requested duty value for forced operation.
VVT Aim Angle #2
VVT target duty (Bank 2)/
Min.: 0%, Max.: 399.9%
-
VVT duty signal value during forced operation.
VVT Change Angle #2
VVT displacement angle (for Intake Side of Bank 2)/
Min.: 0 DegFR, Max.: 639.9 DegFR
-
Displacement angle during forced operation.
VVT OCV Duty #2
Camshaft timing oil control valve operation duty (Bank 2)/
Min.: 0%, Max.: 399.9%
-
Requested duty value for forced operation.
VVT Ex Hold Lrn Val #1
VVT exhaust hold duty ratio learned value (Bank 1)/
Min.: 0%, Max.: 399.9%
-
Learned duty value for forced operation.
VVT Ex Chg Angle #1
VVT exhaust displacement angle (Bank 1)/
Min.: 0 DegFR, Max.: 639.9 DegFR
-
Displacement angle during forced operation.
VVT Ex OCV Duty #1
Camshaft timing oil control valve duty (for Exhaust Side of Bank 1)/
Min.: 0%, Max.: 399.9%
-
Requested duty value for forced operation.
VVT Ex Hold Lrn Val #2
VVT exhaust hold duty ratio learned value (Bank 2)/
Min.: 0%, Max.: 399.9%
-
Learned duty value for forced operation.
VVT Ex Chg Angle #2
VVT exhaust displacement angle (Bank 2)/
Min.: 0 DegFR, Max.: 639.9 DegFR
-
Displacement angle during forced operation.
VVT Ex OCV Duty #2
Camshaft timing oil control valve duty (for Exhaust Side of Bank 2)/
Min.: 0%, Max.: 399.9%
-
Requested duty value for forced operation.
VN Turbo Type
VN turbo type/
Not Avl, Commo, Vacuum or CAN Com
Not Avl
-
Catalyst Temp B1S1
Catalyst temperature (Bank 1, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B2S1
Catalyst temperature (Bank 2, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B1S2
Catalyst temperature (Bank 1, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B2S2
Catalyst temperature (Bank 2, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
-
-
Starter Signal
Starter signal/
Close or Open
Open: Cranking
-
Starter Control
Starter switch status/
ON or OFF
ON: Cranking
-
Power Steering Signal
Power steering oil pressure sensor signal/
ON or OFF
ON: Power steering operating
-
Starter Relay
Starter relay status/
ON or OFF
ON: Cranking
-
ACC Relay
ACC relay status/
ON or OFF
ON: Cranking
-
Neutral Position SW Signal
PNP switch status/
ON or OFF
ON: P or N position
-
Clutch Switch
Clutch switch status/
ON or OFF
ON: Clutch pedal depressed
-
Clutch Start SW
Clutch start switch status/
ON or OFF
ON: Clutch pedal depressed
-
Transfer L4
L4 status of the transfer/
ON or OFF
ON: 4WD control switch in 4L position
-
Stop Light Switch
Stop light switch/
ON or OFF
ON: Brake pedal depressed
-
A/C Signal
A/C switch status/
ON or OFF
ON: A/C on
-
Closed Throttle Position SW
Closed throttle position switch/
ON or OFF
- ON: Throttle fully closed
- OFF: Throttle open
-
Fuel Cut Condition
Fuel cut condition/
ON or OFF
ON: Fuel cut operating
-
Immobiliser Communication
Immobiliser communication/
ON or OFF
ON: Normal
-
Check Mode
Check mode/
ON or OFF
ON: Check mode on
Refer to Check Mode Procedure (Click here).
SPD Test Result
Check mode result for vehicle speed sensor/
Compl or Incmpl
-
-
AS Test Result
Check mode result for secondary air injection system/
Compl or Incmpl
-
-
Misfire Test Result
Check mode result for misfire monitor/
Compl or Incmpl
-
-
OXS1 Test Result
Check mode result for heated oxygen sensor (Bank 1)/
Compl or Incmpl
-
-
OXS2 Test Result
Check mode result for heated oxygen sensor (Bank 2)/
Compl or Incmpl
-
-
A/F Test Results #2
Check mode result for air fuel ratio sensor (Bank 2)/
Compl or Incmpl
-
-
A/F Test Results #1
Check mode result for air fuel ratio sensor (Bank 1)/
Compl or Incmpl
-
-
Complete Parts Monitor
Comprehensive component monitor/
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor/
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor/
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor/
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor/
Compl or Incmpl
-
-
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Not Avl or Avail
-
-
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Compl or Incmpl
-
-
O2S(A/FS) Monitor
O2S (A/FS) monitor/
Not Avl or Avail
-
-
O2S(A/FS) Monitor
O2S (A/FS) monitor/
Compl or Incmpl
-
-
A/C Monitor
A/C monitor/
Not Avl or Avail
-
-
A/C Monitor
A/C monitor/
Compl or Incmpl
-
-
2nd Air Monitor
2nd air monitor/
Not Avl or Avail
-
-
2nd Air Monitor
2nd air monitor/
Compl or Incmpl
-
-
EVAP Monitor
EVAP monitor/
Not Avl or Avail
-
-
EVAP Monitor
EVAP monitor/
Compl or Incmpl
-
-
Heated Catalyst Monitor
Heated catalyst monitor/
Not Avl or Avail
-
-
Heated Catalyst Monitor
Heated catalyst monitor/
Compl or Incmpl
-
-
Catalyst Monitor
Catalyst monitor/
Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor/
Compl or Incmpl
-
-
TC Terminal
TC terminal status/
ON or OFF
-
-
# Codes (Include History)
Number of codes/
Min.: 0, Max.: 255
-
Number of DTCs stored.
MIL
MIL status/
ON or OFF
ON: MIL on
-
MIL ON Run Distance
Distance driven with MIL on/
Min.: 0 km, Max.: 65535 km
Distance driven after DTC stored
-
Running Time from MIL ON
Running time from MIL ON/
Min.: 0 min, Max.: 65535 min
Running time after MIL turned on
-
Time after DTC Cleared
Time after DTCs cleared/
Min.: 0 min, Max.: 65535 min
Time after DTCs cleared
-
Distance from DTC Cleared
Distance driven after DTCs cleared/
Min.: 0 km, Max.: 65535 km
Distance driven after DTCs cleared
-
Warmup Cycle Cleared DTC
Warmup cycles after DTCs cleared/
Min.: 0, Max.: 255
-
Number of warmup cycles after the DTCs are cleared.
Dist Batt Cable Disconnect
Distance driven after battery cable disconnected/
Min.: 0 km, Max.: 65535 km
Total distance vehicle driven after battery cable disconnected
-
IG OFF Elapsed Time
Time after ignition switch turned off/
Min.: 0 min, Max.: 655350 min
Cumulative time after ignition switch turned off
-
OBD Requirements
OBD requirement
EOBD (Euro OBD)
-
Number of Emission DTC
Emissions-related DTCs
-
Number of emissions-related DTCs.
TC and TE1
TC and CG (TE1) terminals of DLC3/
ON or OFF
-
-
Ignition Trig. Count
Ignition counter/
Min.: 0, Max.: 65535
0 to 600
-
Cylinder #1 Misfire Count
to
Cylinder #6 Misfire Count
Misfire count of cylinder 1 to 6/
Min.: 0, Max.: 255
0
-
All Cylinders Misfire Count
Misfire count of all cylinders/
Min.: 0, Max.: 255
0 to 35
-
Misfire RPM
Engine speed for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Misfire 0
-
Misfire Load
Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: Misfire 0
-
Misfire Margin
Misfire monitoring/
Min.: -128%, Max.: 127%
0 to 99.2%
Misfire detection margin.
Catalyst OT MF F/C
Fuel cut to prevent catalyst from overheating during misfire/
Not Avl or Avail
Avail: Fuel cut to prevent catalyst from overheating during misfire available
Not Avl: Fuel cut to prevent catalyst from overheating during misfire not available
-
Cat OT MF F/C History
History of fuel cut to prevent catalyst from overheating during misfire/
ON or OFF
ON: Fuel cut operation history exists
-
Cat OT MF F/C Cylinder #1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
Cat OT MF F/C Cylinder #2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
Cat OT MF F/C Cylinder #3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
Cat OT MF F/C Cylinder #4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
Cat OT MF F/C Cylinder #5
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
Cat OT MF F/C Cylinder #6
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/
ON or OFF
ON: Fuel cut operating
-
Engine Speed (Starter Off)
Engine speed when starter off/
Min.: 0 rpm, Max.: 51199 rpm
-
For use when engine stall, starting problems or rough idle is present.
Starter Count
Number of times starter turned on after ignition switch turned to ON/
Min.: 0, Max.: 255
-
For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip
Distance driven during previous trip/
Min.: 0 km, Max.: 655.35 km
-
Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.- HINT:
- Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.
Engine Starting Time
Time elapsed after engine started (interval between ignition switch to ON and off)/
Min.: 0 ms, Max.: 655350 ms
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp
Engine coolant temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp
Intake air temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature
Engine oil temperature (estimated temperature)/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C
Ambient temperature for A/C/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp
Ambient temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation
History of hesitation during engine start/
ON or OFF
-
-
Low Rev for Eng Start
History of low engine speed after engine start/
ON or OFF
-
-
Minimum Engine Speed
Minimum engine speed/
Min.: 0 rpm, Max.: 51199 rpm
-
For use when engine stall, starting problems or rough idle is present.
Power Steering Pressure
Power steering oil pressure/
Min.: 0 MPa, Max.: 11 MPa
-
-
ACT VSV
A/C cut status for Active Test/
ON or OFF
-
-
Brake Override System
Brake override system status/
ON or OFF
ON: Brake override system operating
-
Idle Fuel Cut
Fuel cut at idle/
ON or OFF
ON: Fuel cut operating
Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
FC TAU
Fuel cut TAU (fuel cut during very light load)/
ON or OFF
ON: Fuel cut operating
The fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete.
Immobiliser Fuel Cut
Status of immobiliser fuel cut/
ON or OFF
-
-
Immobiliser Fuel Cut History
Status of the immobiliser fuel cut history/
ON or OFF
-
-
Cruise Cancel Signal
Status of the cruise cancel signal/
ON or OFF
-
-
Model Code
Model code
-
Used for identifying the model code:
GRJ2##
Engine Type
Engine type
-
Used for identifying the engine type:
1GRFE
Cylinder Number
Number of cylinders/
Min.: 0, Max.: 255
-
Used for identifying the number of cylinders:
6
Transmission Type
Transmission type
-
Used for identifying the transmission type:
ECT 5th
Transmission Type2
Transmission type 2
-
-
Destination
Destination
-
Used for identifying the destination:
W
Model Year
Model year/
Min.: 1900, Max.: 2155
-
Used for identifying the model year:
20##
System Identification
System identification
-
Used for identifying the engine system:
Gasoline (gasoline engine)
Engine Speed of Cyl #1
Engine speed for cylinder 1/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #2
Engine speed for cylinder 2/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #3
Engine speed for cylinder 3/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #4
Engine speed for cylinder 4/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #5
Engine speed for cylinder 5/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #6
Engine speed for cylinder 6/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Av Engine Speed of All Cyl
Engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
SPD (NT)
Input shaft speed/
Min.: 0 rpm, Max.: 12750 rpm
- Lock-up on (after warming up engine): Input turbine speed (NT) equal to engine speed
- Lock-up off (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
Data is displayed in increments of 50 rpm.
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
-
Overdrive Cut Switch #1
Overdrive cut signal for cruise control/
ON or OFF
-
-
Shift SW Status (P Range)
PNP switch status (P)/
ON or OFF
- Shift lever in P: ON
- Shift lever not in P: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Pattern Switch (PWR/M)
Pattern switch (PWR) status/
ON or OFF
- ON: Pattern switch (PWR) is pushed
- OFF: Pattern switch (PWR) is not pushed
-
Shift SW Status (R Range)
PNP switch status (R)/
ON or OFF
- Shift lever in R: ON
- Shift lever not in R: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (N Range)
PNP switch status (N)/
ON or OFF
- Shift lever in N: ON
- Shift lever not in N: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (N, P Range) Supported
Status of park/neutral position switch (N or P) supported/
Supp or Unsupp
-
-
Shift SW Status (N, P Range)
Park/neutral position switch status (N or P)/
ON or OFF
- ON: Shift lever not in P or N
- OFF: Shift lever in P or N
-
Sports Shift Up SW
Sport shift up switch status/
ON or OFF
- ON: Shift lever held in "+" (up-shift)
- OFF: Shift lever not in "+" (up-shift)
-
Sports Shift Down SW
Sport shift down switch status/
ON or OFF
- ON: Shift lever held in "-" (down-shift)
- OFF: Shift lever not in "-" (down-shift)
-
Sports Mode Selection SW
Sport mode select switch status/
ON or OFF
- ON: Shift lever in S, "+" or "-"
- OFF: Shift lever not in S, "+" or "-"
-
Shift SW Status (D Range)
PNP switch status (D)/
ON or OFF
- Shift lever in D, S, "+" or "-": ON
- Shift lever not in D, S, "+" or "-": OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
A/T Oil Temperature 1
No. 1 ATF temperature sensor value/
Min.: -40°C, Max.: 150°C
- After stall test:
Approximately 80°C (176°F)
- Equal to ambient temperature when engine cold
If the value is -40°C (-40°F) or 150°C (302°F), the No. 1 ATF temperature sensor circuit is open or shorted.
A/T Oil Temperature 2
No. 2 ATF temperature sensor value/
Min.: -40°C, Max.: 150°C
- After stall test:
Approximately 80°C (176°F)
- Equal to ambient temperature when engine cold
If the value is -40°C (-40°F) or 150°C (302°F), the No. 2 ATF temperature sensor circuit is open or shorted.
Lock Up
Lock-up/
ON or OFF
- Lock-up operating: ON
- Lock-up not operating: OFF
-
Shift Status
ECM gear shift command/
1st, 2nd, 3rd, 4th or 5th
Shift lever in D or S: 1st, 2nd, 3rd, 4th or 5th
-
SLT Solenoid Status
Shift solenoid SLT status/
ON or OFF
- Accelerator pedal depressed: OFF
- Accelerator pedal released: ON
-
SLU Solenoid Status
Shift solenoid SLU status/
ON or OFF
- Shift solenoid operating: ON
- Shift solenoid not operating: OFF
-
Snow or 2nd Start Mode
Pattern switch (2nd) status/
ON or OFF
- ON: 2nd mode on
- OFF: 2nd mode off
-
AT Fluid
Flex lock-up judder judgment/
ON or OFF
- ON: Judder judgment occurs
- OFF: Judder judgment does not occur
-
- *: This excludes the throttle valve opening percentage due to Idle Speed Control (ISC).
- HINT:
- Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.
- 10 to 16.4%: Idling
| ACTIVE TEST |
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
Tester Display
Test Part
Control Range
Diagnostic Note
Control the Injection Volume
Change injection volume
Between -12.5% and 24.8%
- All fuel injectors are tested at the same time.
- Perform the test at or below 3000 rpm.
- The injection volume can be changed in 1% gradations within the control range.
Control the Injection Volume for A/F Sensor
Change injection volume
-12.5% / 0% / 12.5%
- Perform the test at or below 3000 rpm.
- Control the Injection Volume for A/F Sensor enables the checking and graphing of the air fuel ratio sensor voltage outputs.
- To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2.
Activate the VSV for Secondary Air Control
Activate the secondary air system
ON/OFF
- Do not perform this test for 5 seconds or more.
- After the test, do not perform the test again for 30 seconds.
Activate the VSV for Evap Control
Activate purge VSV control
ON/OFF
-
Control the A/C Cut Signal
Control A/C cut signal
ON/OFF
-
Control the Fuel Pump / Speed
Activate fuel pump
ON/OFF
This test is possible when the following conditions are met: - The ignition switch is ON.
- The engine is not started.
- The shift lever is in P.
Control the Fuel Pump Duty
Activate fuel pump
25%/80%
This test is possible when the following conditions are met: - The ignition switch is ON.
- The engine is not started.
- The shift lever is in P.
Connect the TC and TE1
Turn on and off TC and TE1 connection
ON/OFF
- ON: TC and TE1 are connected.
- OFF: TC and TE1 are disconnected.
Control the Idle Fuel Cut Prohibit
Prohibit idling fuel cut control
ON/OFF
-
Prohibit the Catalyst OT Misfire prevent F/C
Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire
ON: Fuel cut prohibited
Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less.
Activate the Starter Relay
Activate the starter relay
ON/OFF
Perform this test with the engine stopped.
Activate the ACC Cut Relay
Activate the ACC Cut relay
ON/OFF
Perform this test with the engine stopped.
Control the ETCS Open/Close Slow Speed
Throttle actuator
Close/Open
Open: Throttle valve opens slowly
This test is possible when the following conditions are met: - The ignition switch is ON.
- The engine is stopped.
- The accelerator pedal is fully depressed (APP: 58 degrees or more).
- The shift lever is in P.
Control the ETCS Open/Close Fast Speed
Throttle actuator
Close/Open
Open: Throttle valve opens quickly
Same as above.
Control the VVT Linear (Bank 1)
Control Variable Valve Timing (VVT) [Bank 1]
-128 to 127% (this value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
- Engine stalls or idles roughly when the VVT actuator is operated at 100%.
- Test is possible during idle.
- DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the VVT System (Bank 1)
Turn camshaft timing oil control valve on and off
ON/OFF
- Engine stalls or idles roughly when the camshaft timing oil control valve is turned on.
- Engine runs and idles normally when the camshaft timing oil control valve is off.
- DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the VVT Linear (Bank 2)
Control Variable Valve Timing (VVT) [Bank 2]
-128 to 127% (this value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
- Engine stalls or idles roughly when the VVT actuator is operated at 100%.
- Test is possible during idle.
- DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the VVT System (Bank 2)
Turn camshaft timing oil control valve on and off
ON/OFF
- Engine stalls or idles roughly when the camshaft timing oil control valve is turned on.
- Engine runs and idles normally when the camshaft timing oil control valve is off.
- DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the VVT Exhaust Linear (Bank 1)
Control VVT (Bank 1)
-128 to 127% (this value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
- Engine stalls or idles roughly when the VVT actuator is operated at 100%.
- Test is possible during idle.
- DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the VVT Exhaust Linear (Bank 2)
Control VVT (Bank 2)
-128 to 127% (this value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
- Engine stalls or idles roughly when the VVT actuator is operated at 100%.
- Test is possible during idle.
- DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Activate the Air Pump Heater
Activate air pump heater
ON/OFF
- This test activates the air pump heater for up to 60 seconds.
- To protect the air pump heater, do not perform this test more than 4 times in a row.
Control the Select Cylinder Fuel Cut
Selected cylinder (cylinder #1 to #6) injector fuel cut
#1/#2/#3/#4/#5/#6
ON/OFF
Test is possible while the vehicle is stopped and the engine is idling.*1
Control the All Cylinders Fuel Cut
Fuel cut for all cylinders
ON/OFF
Test is possible while the vehicle is stopped and the engine is idling.*1
Check the Cylinder Compression*2
Check the cylinder compression pressure
ON/OFF
Fuel injection and ignition stop in all cylinders.
- NOTICE:
-
*1:
- If the display of the Data List item Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
- If the display of the Data List item Catalyst OT MF F/C item is Avail, perform this Active Test as described below.
- Stop the engine, turn the ignition switch to ON.
- Enter the Control the Select Cylinder Fuel Cut.
- Select the cylinder for fuel cut (cylinder #1 to #6) and turn the Active Test ON (press the RIGHT or LEFT button).
- Start the engine.
- If the display of the Data List item Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
- HINT:
- *2: When cranking the engine, the speed of each cylinder is measured.
- In this Active Test, the fuel and ignition of all cylinders are cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.
- Warm up the engine.
- Turn the ignition switch off.
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON.
- Turn the GTS on.
- Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.
- HINT:
- To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.
- Push the snapshot button to turn the snapshot function on.
- HINT:
- Using the snapshot function, data can be recorded during the Active Test.
- While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.
- HINT:
- After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.
- Crank the engine for about 10 seconds.
- HINT:
- Continue to crank the engine until the values change from the default value (51199 rpm).
-
Monitor the engine speed (Engine Speed of Cyl #1 to #6) displayed on the GTS.

- HINT:
- At first, the GTS displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.
- NOTICE:
- Do not crank the engine continuously for 20 seconds or more.
- If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.
- Use a fully-charged battery.
- Do not crank the engine continuously for 20 seconds or more.
- Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.
- NOTICE:
- If the Active Test is changed to OFF while the engine is being cranked, the engine will start.
- Push the snapshot button to turn the snapshot function off.
- Select "Stored Data" on the GTS screen, select the recorded data and display the data as a graph.
- HINT:
- If the data is not displayed as a graph, the change of the values cannot be observed.
- Check the change in engine speed values.
- HINT:
- As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.
- All fuel injectors are tested at the same time.
| SYSTEM CHECK |
- HINT:
- Performing a system check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are stored, and can detect potential malfunctions in the system. The system check can be performed with the GTS.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility.
Perform the system check by referring to the table below.
Tester Display
Test Part
Control Range
Diagnostic Note
Secondary Air Injection Check (Automatic Mode)
Perform secondary air injection system operation automatically
With warm engine, ignition switch turned off once
- If no pending DTCs are output after performing this test, the system is functioning normally.
- Refer to the inspection procedure for secondary air injection system DTCs.
- When performing Secondary Air Injection Check after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when System Check finishes.
Secondary Air Injection Check (Manual Mode)
Perform 5 operations in order to operate secondary air injection system monitor manually
With warm engine, ignition switch turned off once
- Used to detect malfunctioning parts.
- Refer to the inspection procedure for secondary air injection system DTCs.
- When performing Secondary Air Injection Check after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
- Turn the ignition switch off when System Check finishes.
- If no pending DTCs are output after performing this test, the system is functioning normally.