2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

FAIL-SAFE CHART

System information · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.
DTC
Component
Fail-Safe Operation
Fail-Safe Deactivation Condition
P0011, P0021, P0015 and P0025*3
Camshaft oil control valve (OCV)
  1. Idle up (control of combustion worsening)
  2. Stopping fuel cut control
Pass condition detected
P0031, P0032, P0051, P0052 and P102D and P105D
Air Fuel ratio (A/F) Sensor Heater
The ECM turns off the A/F sensor heater.
Engine switch off
P0037, P0038, P0057, P0058, P101D and P103D
Heated Oxygen (HO2) Sensor Heater
The ECM turns off the HO2 sensor heater.
Engine switch off
P0102 and P0103
Mass Air Flow (MAF) Meter
The ECM calculates ignition timing according to the engine speed and throttle valve position.
Pass condition detected
P0112 and P0113
Intake Air Temperature (IAT) Sensor
The ECM estimates the IAT to be 20°C (68°F).
Pass condition detected
P0115, P0117 and P0118
Engine Coolant Temperature (ECT) Sensor
The ECM estimates the ECT to be 80°C (176°F).
Pass condition detected
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P2102, P2103, P2111, P2112, P2118, P2119 and P2135
Electronic Throttle Control System (ETCS)
The ECM cuts off throttle actuator current and the throttle valve is returned to a 7° throttle position by the return spring.
The ECM then adjusts the engine output by controlling fuel injection (intermittent fuel cut) and ignition timing in accordance with the accelerator pedal opening angle to allow the vehicle to continue at minimal speed*1.
Pass condition detected and then engine switch turned off
P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308*2
  1. Fuel injector
  2. Electronic Throttle Control System (ETCS)
When a misfire occurs, fuel cut is performed for catalyst overheat malfunction prevention.
  1. With a normal load and normal engine speed (MIL is blinking):
    - Fuel cut is performed on the malfunctioning cylinder.
  2. With a high load and high engine speed driving (MIL is blinking):
    - Throttle valve opening angle control is performed.
    - Fuel cut is performed on all cylinders or the malfunction cylinder.
Pass condition detected and then engine switch turned off
P0327, P0328, P032C, P032D, P0332, P0333, P033C and P033D
Knock Sensor
The ECM sets the ignition timing to maximum retard.
Engine switch off
P0351 to P0358
Ignition Coil
The ECM cuts fuel.
Pass condition detected
P0504
Stop Light Switch
The accelerator pedal angle is fixed.
Accelerator pedal angle is fixed
P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138
Accelerator Pedal Position (APP) Sensor
The APP sensor has 2 sensor circuits: Main and Sub.
If either circuit malfunctions, the ECM controls the engine using the other circuit.
If both circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Pass condition detected and then engine switch turned off

HINT:
  1. *1: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.
  2. *2: Misfire related fail-safe operations occur when catalyst overheat malfunctions occur.
  3. *3: Only for M-OBD.

← FAIL-SAFE CHART (Sep 2011 – Dec 2011)DATA LIST / ACTIVE TEST (Sep 2011 – Dec 2011) →