2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

DATA LIST / ACTIVE TEST

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  7. According to the display on the intelligent tester, read the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed
    The speed is indicated on speedometer.
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16383 rpm
    650 to 750 rpm: Idling
    -
    Calculate Load
    Calculated load by ECM/
    Min.: 0%, Max.: 100%
    1. 11 to 25%: Idling
    2. 12 to 26%: Running without load (2500 rpm)
    -
    Vehicle Load
    Vehicle load/
    Min.: 0%, Max.: 25700%
    Actual vehicle load
    -
    MAF
    Air flow rate from Mass Air Flow (MAF) meter/
    Min.: 0 gm/s, Max.: 655.35 gm/s
    4.0 to 8.0 gm/s.: Idling
    If the mass air flow volume is approximately 0.0 gm/s.:
    1. The mass air flow meter power source circuit is open or short.
    2. The VG circuit is open or short.
    If the mass air flow volume is 271.0 gm/s. or more:
    1. The E2G circuit is open.
    Atmosphere Pressure
    Atmospheric pressure/
    Min.: 0 kPa, Max.: 255 kPa
    Equivalent to atmospheric pressure (absolute pressure)
    -
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C, Max.: 215°C
    75 to 100°C (167 to 212°F): After warming up
    If the value is -40°C (-40°F): the sensor circuit is open.
    If the value is 140°C (284°F): the sensor circuit is shorted.
    Intake Air
    Intake air temperature/
    Min.: -40°C, Max.: 140°C
    Equivalent to ambient air temperature
    If the value is -40°C (-40°F): the sensor circuit is open.
    If the value is 140°C (284°F): the sensor circuit is shorted.
    Engine Run Time
    Engine run time/
    Min.: 0 s, Max.: 65535 s
    Time after engine start
    Service data.
    Initial Engine Coolant Temp
    Initial engine coolant temperature/
    Min.: -40°C, Max.: 119.3°C
    Coolant temperature when engine started
    Service data.
    Initial Intake Air Temp
    Initial intake air temperature/
    Min.: -40°C, Max.: 119.3°C
    Intake air temperature when engine started
    Service data.
    Battery Voltage
    Battery voltage/
    Min.: 0 V, Max.: 65.535 V
    11 to 14 V: Idling
    -
    Accel Sens. No.1 Volt %
    Absolute Accelerator Pedal Position (APP) No. 1/
    Min.: 0%, Max.: 100%
    10 to 22%: accelerator pedal released
    54 to 86%: accelerator pedal fully depressed
    -
    Accel Sens. No.2 Volt %
    Absolute APP No. 2/
    Min.: 0%, Max.: 100%
    12 to 42%: accelerator pedal released
    66 to 98%: accelerator pedal fully depressed
    -
    Accel Sensor Out No.1
    APP sensor No. 1 voltage/
    Min.: 0 V, Max.: 4.980 V
    -
    ECT Service data.
    Accel Sensor Out No.2
    APP sensor No. 2 voltage/
    Min.: 0 V, Max.: 4.980 V
    -
    ECT Service data.
    Accel Sensor Out No.1
    APP sensor No. 1 voltage/
    Min.: 0 V, Max.: 4.980 V
    0.5 to 1.1 V: accelerator pedal is released
    2.6 to 4.5 V: accelerator pedal is fully depressed
    -
    Accel Sensor Out No.2
    APP sensor No. 2 voltage/
    Min.: 0 V, Max.: 4.980 V
    1.2 to 2.0 V: accelerator pedal is released
    3.4 to 5.0 V: accelerator pedal is fully depressed
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Accel Fully Close #1 (AD)
    Accelerator fully closed value No. 1 (AD)/
    Min.: 0, Max.: 4.98 V
    -
    ETCS service data
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No. 1/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data.
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No. 2/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data.
    Throttle Sensor Volt %
    Throttle valve opening percentage according to throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Accelerator pedal released
    2. 64 to 96%: Accelerator pedal fully depressed
    Value calculated based on the voltage at terminal VTA1.
    Throttl Sensor #2 Volt %
    Throttle valve opening percentage according to throttle position sensor No. 2/
    Min.: 0%, Max.: 100%
    1. 42 to 62%: Accelerator pedal released
    2. 92 to 100%: Accelerator pedal fully depressed
    Value calculated based on the voltage at terminal VTA2.
    ST1
    Brake pedal signal/
    ON or OFF
    ON: Brake pedal depressed
    -
    System Guard
    System guard/
    ON or OFF
    -
    ETCS service data.
    Open Side Malfunction
    Open side malfunction/
    ON or OFF
    -
    ETCS service data.
    Throttle Idle Position
    Whether or not throttle position sensor detecting idling/
    ON or OFF
    1. ON: Accelerator pedal released
    2. OFF: Accelerator pedal fully depressed
    -
    Throttle Require Position
    Required throttle position/
    Min.: 0 V, Max.: 4.9 V
    0.5 to 1.1 V: Idling
    -
    Throttle Sensor Position*1
    Throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 0%: Accelerator pedal released
    2. 50 to 80%: Accelerator pedal fully depressed
    Recognition value for throttle opening angle on ECM.
    Throttle Position
    No. 1
    Throttle position sensor No. 1 output voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze data
    Throttle Position
    No. 2
    Throttle position sensor No. 2 output voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze data
    Throttle Position
    No. 1
    Throttle position No. 1/
    Min.: 0 V, Max.: 4.98 V
    1. 0.5 to 1.1 V: Accelerator pedal released
    2. 3.2 to 4.8 V: Accelerator pedal fully depressed
    3. 0.6 to 1.4 V: Fail-safe operating
    -
    Throttle Position
    No. 2
    Throttle position No. 2/
    Min.: 0 V, Max.: 4.98 V
    1. 2.1 to 3.1 V: Accelerator pedal released
    2. 4.6 to 5.0 V: Accelerator pedal fully depressed
    3. 2.1 to 3.1 V: Fail-safe operating
    -
    Throttle Position Command
    Throttle position command value/
    Min.: 0 V, Max.: 4.980 V
    0.5 to 4.8 V
    -
    Throttle Sens Open Pos #1
    Throttle sensor opener position No. 1/
    Min.: 0 V, Max.: 4.980 V
    0.6 to 1.4 V
    ETCS service data.
    Throttle Sens Open Pos #2
    Throttle sensor opener position No. 2/
    Min.: 0 V, Max.: 4.980 V
    1.7 to 2.5 V
    ETCS service data.
    Throttle Sens Open #1(AD)
    Throttle sensor opener position No. 1 (AD)/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 4.8 V
    -
    Throttle Motor
    Whether or not throttle actuator control permitted/
    ON or OFF
    1. ON: Ignition switch ON
    1. OFF: ETCS has failed
    -
    Throttle Motor Current
    Throttle motor current/
    Min.: 0 A, Max.: 19.9 A
    0 to 3.0 A: Idling
    ETCS service data.
    Throttle Motor DUTY
    Throttle actuator/
    Min.: 0%, Max.: 100%
    10 to 22%: Idling after engine warmed up
    ETCS service data.
    Throttle Motor Current
    Throttle actuator current/
    Min.: 0 A, Max.: 19.92 A
    0 to 3.0 A: Idling
    -
    Throttle Motor Open Duty
    Throttle actuator opening duty ratio/
    Min.: 0%, Max.: 255%
    0 to 40%: During idling
    When accelerator pedal depressed, duty ratio increased.
    Throttle Motor Close Duty
    Throttle actuator closed duty ratio/
    Min.: 0%, Max.: 255%
    0 to 40%: During idling
    When accelerator pedal released quickly, duty ratio increased.
    Throttle Motor Duty (Open)
    Throttle actuator duty ratio (open)/
    Min.: 0%, Max.: 255%
    0 to 40%: Idling
    ETCS service data.
    Throttle Motor Duty (Close)
    Throttle actuator duty ratio (closed)/
    Min.: 0%, Max.: 255%
    0 to 40%: Idling
    ETCS service data.
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value)/
    Min.: 0 V, Max.: 4.98 V
    0.4 to 1.0 V: Accelerator pedal released
    -
    ETCS Actuator Power
    Whether or not electric throttle control system power inputted/
    ON or OFF
    1. ON: Ignition switch ON and system normal
    1. OFF: ETCS has failed
    -
    +BM Voltage
    +BM voltage/
    Min.: 0 V, Max.: 79.998 V
    11 to 14 V: Engine switch on (IG) and system normal
    ETCS service data.
    Actuator Power Supply
    Actuator power supply/
    ON or OFF
    ON: Idling
    ETCS service data.
    Clutch Current
    Clutch current/
    Min.: 0 A, Max.: 2.49 A
    -
    -
    Fail Safe Drive
    Whether or not fail-safe function executed/
    ON or OFF
    1. ON: ETCS has failed
    1. OFF: ETCS normal
    ETCS service data.
    Fail Safe Drive (Main CPU)
    Whether or not fail-safe function executed/
    ON or OFF
    1. ON: ETCS has failed
    1. OFF: ETCS normal
    ETCS service data.
    Injector (Port)
    Injection period of the No. 1 cylinder/
    Min.: 0 μs, Max.: 65535 μs
    2000 to 4000 μs: idling
    -
    Injection Volum (Cylinder 1)
    Injection volume (cylinder 1)/
    Min.: 0 ml, Max.: 2.047 ml
    0 to 0.5 ml
    Quantity of fuel injection volume for 10 times.
    Fuel Pump/Speed Status
    Fuel pump/speed status/
    ON or OFF
    -
    -
    EVAP (Purge) VSV
    Purge VSV control duty/
    Min.: 0%, Max.: 100%
    0 to 100%: During idling
    Order signal from ECM.
    Evap Purge Flow
    Purge flow/
    Min.: 0%, Max.: 399.9%
    0 to 100%: Idling
    -
    Purge Density Learn Value
    Learning value of purge density/
    Min.: -200%, Max.: 199.993%
    Idling: -40 to 0%
    Service data.
    EVAP Purge VSV
    VSV status for EVAP control/
    ON or OFF
    -
    -
    Target Air-Fuel Ratio
    Air fuel ratio:
    Min.: 0, Max.: 1.999
    0.8 to 1.2: During idling
    -
    AF Lambda B1S1
    Short-term fuel trim associated with the Bank 1 Sensor 1/
    Min.: 0, Max.: 1.999
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air fuel ratio = 1
    3. Value more than 1 (1.001 to 1.999) = Lean
    -
    AF Lambda B2S1
    Short-term fuel trim associated with the Bank 2 Sensor 1/
    Min.: 0, Max.: 1.999
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air fuel ratio = 1
    3. Value more than 1 (1.001 to 1.999) = Lean
    -
    AFS Voltage B1S1
    Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/
    Min.: 0 V, Max.: 7.999 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    AFS Voltage B2S1
    Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/
    Min.: 0 V, Max.: 7.999 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    AFS Current B1S1
    Air fuel ratio sensor current Bank 1 Sensor 1/
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
    AFS Current B2S1
    Air fuel ratio sensor current (for Bank 2 Sensor 1)/
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
    O2S B1S2
    Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving 70 km/h (44 mph)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    O2S B2S2
    Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving 70 km/h (44 mph)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    Short FT #1
    Short-term fuel trim of Bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
    Long FT #1
    Long-term fuel trim of Bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    This item refers to the overall fuel compensation carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
    Short FT #2
    Short-term fuel trim of Bank 2/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
    Long FT #2
    Long-term fuel trim of Bank 2/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    This item refers to the overall fuel compensation carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
    Fuel System Status #1
    Fuel system status (Bank 1)/
    OL, CL, OLDrive, OLFault or CLFault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
    2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
    3. OLDrive: Open loop due to driving conditions (fuel enrichment).
    4. OLFault: Open loop due to a detected system fault.
    5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
    Fuel System Status #2
    Fuel system status (Bank 2)/
    OL, CL, OLDrive, OLFault or CLFault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
    2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
    3. OLDrive: Open loop due to driving conditions (fuel enrichment).
    4. OLFault: Open loop due to a detected system fault.
    5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
    IGN Advance
    Ignition timing advance for No. 1 cylinder/
    Min.: -64 deg, Max.: 63.5 deg
    BTDC 5 to 15 deg: Idling
    -
    Knock Feedback Value
    Feedback value of knocking/
    Min.: -1024°CA, Max.: 1023.9°CA
    -22 to 0° CA:
    Driving, 70 km/h (44 mph)
    Service data.
    Knock Correct Learn Value
    Correction learning value of knocking/
    Min.: -1024°CA, Max.: 1023.9°CA
    0 to 22° CA:
    Driving, 70 km/h (44 mph)
    Service data.
    ACIS VSV
    VSV status for ACIS control/
    ON or OFF
    -
    -
    VVT Control Status #1
    Variable valve timing (VVT) control status (Bank 1)/
    ON or OFF
    -
    -
    VVT Control Status #2
    VVT control status (Bank 2)/
    ON or OFF
    -
    -
    VVT Aim Angle #1*2
    VVT aim angle (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 80%
    VVT duty signal value during intrusive operation.
    VVT Change Angle #1*2
    VVT change angle (Bank 1)/
    Min.: 0 DegFR, Max.: 639.9 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during intrusive operation.
    VVT OCV Duty #1*2
    VVT OCV operation duty (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for intrusive operation.
    VVT Aim Angle #2*2
    VVT aim angle (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 80%
    VVT duty signal value during intrusive operation.
    VVT Change Angle #2*2
    VVT change angle (Bank 2)/
    Min.: 0 DegFR, Max.: 639.9 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during intrusive operation.
    VVT OCV Duty #2*2
    VVT OCV operation duty (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for intrusive operation.
    VVT Ex Hold Lrn Val #1*2
    VVT exhaust hold duty ratio learning value (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 80%
    VVT duty signal value during intrusive operation.
    VVT Ex Chg Angle #1*2
    VVT exhaust change angle (Bank 1)/
    Min.: 0 DegFR, Max.: 639.9 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during intrusive operation.
    VVT Ex OCV Duty #1*2
    VVT exhaust OCV duty (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for intrusive operation.
    VVT Ex Hold Lrn Val #2*2
    VVT exhaust hold duty ratio learning value (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 80%
    VVT duty signal value during intrusive operation.
    VVT Ex Chg Angle #2*2
    VVT exhaust change angle (Bank 2)/
    Min.: 0 DegFR, Max.: 639.9 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during intrusive operation.
    VVT Ex OCV Duty #2*2
    VVT exhaust OCV duty (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for intrusive operation.
    Catalyst Temp B1S1
    Catalyst temperature (Bank 1, Sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B2S1
    Catalyst temperature (Bank 2, Sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B1S2
    Catalyst temperature (Bank 1, Sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B2S2
    Catalyst temperature (Bank 2, Sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Starter Signal
    Starter signal/
    Open or Close
    Open: Cranking
    -
    Starter Control
    Starter switch status/
    ON or OFF
    ON: Cranking
    -
    Power Steering Signal Record
    Power steering switch signal/
    ON or OFF
    ON: Power steering operation
    -
    Starter Relay
    Starter relay status/
    ON or OFF
    ON: Cranking
    -
    Power Steer. Sig. Record
    Power steering signal (history)/
    ON or OFF
    ON: When steering wheel first turned after battery terminals connected
    This signal status is usually ON until the cables are disconnected from the battery terminals.
    ACC Relay
    Acc relay status/
    ON or OFF
    ON: Cranking
    -
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    ON: Shift lever in P or N
    -
    Stop Light Switch
    Stop light switch/
    ON or OFF
    ON: Brake pedal depressed
    -
    A/C Signal
    A/C switch status/
    ON or OFF
    ON: A/C ON
    -
    Closed Throttle Position SW
    Closed throttle position switch/
    ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    Fuel Cut Condition
    Fuel cut condition/
    ON or OFF
    ON: Fuel cut operating
    -
    Immobiliser Communication
    Immobiliser communication/
    ON or OFF
    ON: Normal
    -
    Electrical Load Signal
    Electrical load signal/
    ON or OFF
    ON: Headlights or defogger is turned ON
    -
    Check Mode
    Check mode/
    ON or OFF
    ON: Check mode ON
    Refer to the Check Mode Procedure
    (Click here).
    SPD Test Result
    Check mode result for vehicle speed sensor/
    Compl or Incmpl
    -
    -
    Misfire Test Result
    Check mode result for misfire monitor/
    Compl or Incmpl
    -
    -
    OXS1 Test Result
    Check mode result for heated oxygen sensor (Bank 1)/
    Compl or Incmpl
    -
    -
    OXS2 Test Result
    Check mode result for heated oxygen sensor (Bank 2)/
    Compl or Incmpl
    -
    -
    A/F Test Results #2
    Check mode result for air fuel ratio sensor (Bank 2)/
    Compl or Incmpl
    -
    -
    A/F Test Results #1
    Check mode result for air fuel ratio sensor (Bank 1)/
    Compl or Incmpl
    -
    -
    Complete Parts Monitor
    Comprehensive component monitor/
    Not Avl or Avail
    -
    -
    Fuel System Monitor
    Fuel system monitor/
    Not Avl or Avail
    -
    -
    Misfire Monitor
    Misfire monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Compl or Incmpl
    -
    -
    A/C Monitor
    A/C Monitor/
    Not Avl or Avail
    -
    -
    A/C Monitor
    A/C Monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Not Avl or Avail
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor
    EVAP monitor/
    Not Avl or Avail
    -
    -
    EVAP Monitor
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Not Avl or Avail
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Not Avl or Avail
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    # Codes (Include History)
    Number of codes/
    Min.: 0, Max.: 255
    -
    Number of stored DTCs.
    MIL
    MIL status/
    ON or OFF
    ON: MIL on
    -
    MIL ON Run Distance
    MIL on run distance/
    Min.: 0 km, Max.: 65535 km
    Distance after DTC stored
    -
    Running Time from MIL ON
    Running time from MIL on/
    Min.: 0 min, Max.: 65535 min
    Equivalent to running time after MIL on
    -
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 minutes, Max.: 65535 minutes
    Equivalent to time after DTCs cleared
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km, Max.: 65535 km
    Equivalent to drive distance after DTCs cleared
    -
    Warmup Cycle Cleared DTC
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after the DTC is cleared.
    OBD Requirements
    OBD requirement
    OBD2
    -
    Number of Emission DTC
    Emission related DTCs
    -
    Number of emission related DTCs.
    TC and TE1
    TC and TE1 terminal of DLC3/
    ON or OFF
    -
    -
    Ignition Trig. Count
    Ignition counter/
    Min.: 0, Max.: 65535
    0 to 800
    -
    Cylinder #1 Misfire Count
    to
    Cylinder #8 Misfire Count
    Misfire count of the cylinder 1 to 8/
    Min.: 0, Max.: 255
    0
    -
    All Cylinders Misfire Count
    All cylinders misfire count/
    Min.: 0, Max.: 255
    0 to 35
    -
    Multi Cylinders Misfire Count
    Multiple cylinder misfire count/
    Min.: 0 Max.: 65535
    0 to 65535
    -
    Misfire RPM
    Engine speed for first misfire range/
    Min.: 0 rpm, Max.: 6375 rpm
    0 rpm: Misfire 0
    -
    Misfire Load
    Engine load for first misfire range/
    Min.: 0 g/rev, Max.: 3.98 g/rev
    0 g/rev: Misfire 0
    -
    Misfire Margin
    Misfire monitoring/
    Min.: -128%, Max.: 127%
    -100 to 99.2%
    Misfire detecting margin
    Catalyst OT MF F/C
    Catalyst over temperature misfire prevention F/C/
    Not Avl or Avail
    Avail: Cat OT MF F/C available
    Not Avl: Cat OT MF F/C not available
    -
    Cat OT MF F/C History
    Catalyst over temperature misfire prevention F/C history/
    ON or OFF
    OFF: Fuel cut operation not exists
    -
    Cat OT MF F/C Cylinder #1
    Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #2
    Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #3
    Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #4
    Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #5
    Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #6
    Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #7
    Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Cat OT MF F/C Cylinder #8
    Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut operating
    -
    Power Steering Pressure
    Power steering oil pressure/
    Min.: 0 MPa, Max.: 25.599 MPa
    -
    -
    ACT VSV
    A/C cut status for Active Test/
    ON or OFF
    -
    -
    Idle Fuel Cut
    Fuel cut idle/
    ON or OFF
    ON: Fuel cut operation
    Idle Fuel Cut is "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
    FC TAU
    Fuel cut TAU: Fuel cut during very light load/
    ON or OFF
    ON: Fuel cut operation
    The fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete.
    Model Code
    Model code
    -
    Identifying the model code:
    URJ2###.
    Engine Type
    Engine type
    -
    Identifying the engine type:
    3URFE.
    Cylinder Number
    Number of cylinders/
    Min.: 0, Max.: 255
    -
    Identifying the number of cylinders:
    8.
    Transmission Type
    Transmission type
    -
    Identifying the transmission type:
    ECT 6th.
    Destination
    Destination
    -
    Identifying the destination:
    W.
    Model Year
    Model year/
    Min.: 1900, Max.: 2155
    -
    Identifying the model year:
    20##.
    Engine Speed of Cyl #1
    Engine speed for cylinder 1/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #2
    Engine speed for cylinder 2/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #3
    Engine speed for cylinder 3/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #4
    Engine speed for cylinder 4/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #5
    Engine speed for cylinder 5/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #6
    Engine speed for cylinder 6/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #7
    Engine speed for cylinder 7/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #8
    Engine speed for cylinder 8/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Av Engine Speed of All Cyl
    Engine speed for all cylinders/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm, Max.: 12750 rpm
    Lock-up is
    1. ON (after warming up engine): Input turbine speed (NT) equal to engine speed
    2. OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
    Data is displayed in increments of 50 rpm.
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
    -

HINT:
  1. Normal Condition: If no conditions are specifically stated for "idling", the shift lever is in N or P, the A/C switch is off and all accessory switches are off.
  2. *1: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).
  3. *2: Data List values are only displayed when performing the following Active Tests: Control the VVT Linear (Bank 1), Control the VVT Linear (Bank 2), Control the VVT Exhaust Linear (Bank 1) and Control the VVT Exhaust Linear (Bank 2). For other Active Tests, the Data List value will be 0.


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the intelligent tester, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12.5% and 24.8%
    1. All the injectors are tested at the same time.
    2. Perform the test at 3000 rpm or less.
    3. The injection volume can be changed in 0.1 or 0.2% graduations within the control range.
    Control the Injection Volume for A/F Sensor
    Change injection volume
    Lower by 12.5% or increase 24.8%
    1. Perform the test at 3000 rpm or less.
    2. Control the Injection Volume for A/F Sensor enables the checking and graphing of the A/F (Air Fuel Ratio) sensor voltage outputs.
    3. To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S1.
    Activate the VSV for Intake Control
    Activate VSV for intake control
    ON/OFF
    -
    Activate the VSV for Evap Control
    Activate purge VSV control
    ON/OFF
    -
    Control the A/C Cut Signal
    Control A/C cut signal
    ON/OFF
    Test possible when
    1. Engine switch is on (IG).
    2. Engine is stopped.
    Control the Fuel Pump / Speed
    Activate fuel pump
    ON/OFF
    Test possible when
    1. Engine switch is on (IG).
    2. Engine is stopped.
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 connected.
    2. OFF: TC and TE1 disconnected.
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    -
    Prohibit the Catalyst OT Misfire prevent F/C
    Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire
    ON/OFF
    ON: Fuel cut is prohibited
    Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less.
    Activate the Starter Relay
    Activate the starter relay
    ON/OFF
    Engine is stopped.
    Activate the ACC Cut Relay
    Activate the ACC CUT relay
    ON/OFF
    Engine is stopped.
    Control the ETCS Open/Close Slow Speed
    Throttle actuator
    Close/Open
    Open: throttle valve opens slowly
    This test is possible when the following conditions are met:
    1. The engine switch is on (IG).
    1. The engine does not starts.
    1. Fully depressing the accelerator pedal (APP: 58 degrees or more).
    Control the ETCS Open/Close Fast Speed
    Throttle actuator
    Close/Open
    Open: throttle valve opens fast
    Same as above.
    Control the VVT Linear (Bank 1)
    Control Variable Valve Timing (VVT) [Bank 1]
    -128 to 127% This valve added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
    2. Test is possible during idle.
    Control the VVT System (Bank 1)
    Turn on and off Oil Control Valve (OCV)
    ON/OFF
    1. Engine stalls or idles roughly when OCV is turned on.
    2. Engine runs or idles normally when OCV is OFF.
    Control the VVT Linear (Bank 2)
    Control Variable Valve Timing (VVT) [Bank 2]
    -128 to 127% This valve added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
    2. Test is possible during idle.
    Control the VVT System (Bank 2)
    Turn on and off Oil Control Valve (OCV)
    ON/OFF
    1. Engine stalls or idles roughly when OCV is turned on.
    2. Engine runs or idles normally when OCV is OFF.
    Control the VVT Exhaust Linear (Bank 1)
    Control VVT (Bank 1)
    128 to 127% This valve added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
    2. Test is possible while engine is idling.
    Control the VVT Exhaust Linear (Bank 2)
    Control VVT (Bank 2)
    128 to 127% This valve added to present OCV control duty
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stalls or idles roughly when VVT actuator is operated by 100%.
    2. Test is possible while engine is idling.
    Control the Cylinder #1 Fuel Cut
    Cylinder #1 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.*1
    Control the Cylinder #2 Fuel Cut
    Cylinder #2 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.*1
    Control the Cylinder #3 Fuel Cut
    Cylinder #3 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.*1
    Control the Cylinder #4 Fuel Cut
    Cylinder #4 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.*1
    Control the Cylinder #5 Fuel Cut
    Cylinder #5 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.*1
    Control the Cylinder #6 Fuel Cut
    Cylinder #6 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.*1
    Control the Cylinder #7 Fuel Cut
    Cylinder #7 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.*1
    Control the Cylinder #8 Fuel Cut
    Cylinder #8 injector fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.*1
    Control the All Cylinders Fuel Cut
    All cylinder fuel cut
    ON/OFF
    Test is possible while vehicle is stopped and engine is idling.*1
    Check the Cylinder Compression*2
    Check the cylinder compression pressure
    ON/OFF
    Fuel injection and ignition stop in all cylinders.

    NOTICE:
    1. *1: If the display of the Data List Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
    2. *1: If the display of the Data List Catalyst OT MF F/C item is Avail, perform this Active Test as described below.
      1. Stop the engine and turn the engine switch on (IG) to turn Control the Cylinder#1 Fuel Cut (to Control the Cylinder#8 Fuel Cut) on.
      2. Start the engine.

    HINT:
    *2: When cranking the engine, each cylinder measures the engine speed.
    In this Active Test, the fuel and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

    1. Warm up the engine.
    2. Turn the engine switch off.
    3. Connect the intelligent tester to the DLC3.
    4. Turn the engine switch on (IG).
    5. Turn the tester on.
    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

      HINT:
      To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

    7. Push the snapshot button to turn the snapshot function on.

      HINT:
      Using the snapshot function, data can be recorded during the Active Test.

    8. While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

      HINT:
      After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.

    9. Crank the engine for about 10 seconds.

      HINT:
      Continue to crank the engine until the values change from the default value (51199 rpm).

    10. Monitor the engine speed (Engine Speed of Cyl #1 to #8) displayed on the intelligent tester.

      HINT:
      At first, the intelligent tester displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

      NOTICE:
      1. Do not crank the engine continuously for 20 seconds or more.
      2. If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.
      3. Use a fully-charged battery.

    11. Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

      NOTICE:
      If the Active Test is changed to OFF while the engine is being cranked, the engine will start.

    12. Push the snapshot button to turn the snapshot function off.
    13. Select "Stored Data" on the intelligent tester screen, select the recorded data and display the data as a graph.

      HINT:
      If the data is not displayed as a graph, the change of the values cannot be observed.

    14. Check the change in engine speed values.

      HINT:
      As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.

← FAIL-SAFE CHART (from Jan 2012)DATA LIST / ACTIVE TEST (from Jan 2012) →