2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0110 Intake Air Temperature Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

A067628E12
  1. The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).
  2. The IAT sensor is powered by a 5 V power supply from the THA terminal of the ECM, via resistor R.
  3. Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, according to changes in the IAT, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

    HINT:
    When any of DTCs P0110, P0112 and P0113 are stored, the ECM enters fail-safe mode. During fail-safe mode, the IAT is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.

DTC Code
DTC Detection Condition
Trouble Area
P0110
An open or short in the Intake Air Temperature (IAT) sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Open or short in Intake Air Temperature (IAT) sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM
P0112
A short in the IAT sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Short in IAT sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM
P0113
An open in the IAT sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Open in IAT sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM

HINT:
When any of these DTCs are output, check the IAT by entering the following menus: Powertrain / Engine and ECT / Intake Air.
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the IAT. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the IAT sensor and stores a DTC.
Example:
If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the IAT sensor circuit, and stores DTC P0113. Conversely, if the output voltage is below 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0112.
If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

WIRING DIAGRAM

A182111E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ OUTPUT DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0110 is output
    A
    P0112 is output
    B
    P0113 is output
    C



B
Go to step 5

C
Go to step 3
A


2. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Intake Air.

  1. Read the value displayed on the tester.

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    Same as actual IAT
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    1. If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.



B
Go to step 5

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


3. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
A127961E34
  1. Disconnect the Mass Air Flow (MAF) meter connector.

  1. Connect terminals 4 (THA) and 5 (E2) of the MAF meter wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Intake Air.

  1. Read the value displayed on the tester.

    Standard value:
    140°C (284°F) or higher



NG
Go to step 4
OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER (Click here)

4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A182110E02
  1. Disconnect the MAF meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C50-4 (THA) - C45-73 (THA)
    Always
    Below 1 Ω
    C50-5 (E2) - C45-97 (ETHW)
    Always
    Below 1 Ω

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C50-4 (THA) - C46-73 (THA)
    Always
    Below 1 Ω
    C50-5 (E2) - C46-97 (ETHW)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM (Click here)

5. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
A164746E06
  1. Disconnect the MAF meter connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Intake Air.

  1. Read the value displayed on the tester.

    Standard value:
    -40°C (-40°F)



NG
Go to step 6
OK

REPLACE MASS AIR FLOW METER (Click here)

6. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
A182110E03
  1. Disconnect the MAF meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C50-4 (THA) or C45-73 (THA) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C50-4 (THA) or C46-73 (THA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0102 Mass or Volume Air Flow Circuit Low Input (+ P0103) (Sep 2011 – Dec 2011)P0115 Engine Coolant Temperature Circuit Malfunction (+ P0117, P0118) (Sep 2011 – Dec 2011) →