2011-2013 Land Cruiser · Service Manual Vehicle Interior

TERMINALS OF ECU

System information · Vehicles built from Sep 2011


CHECK POSITION CONTROL ECU AND SWITCH (for LHD)
B107920E24
  1. Disconnect the c14 and c15 switch connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    c14-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    c14-5 (+B) - c14-1 (GND)
    L - W-B
    Power source
    Always
    11 to 14 V
    c15-4 (IG) - c14-1 (GND)
    G - W-B
    Engine switch signal
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V
    c15-8 (SYSB) - c14-1 (GND)
    R - W-B
    System power source
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the c14 and c15 switch connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    c14-2 (SLD+) - c14-1 (GND)
    B - W-B
    Sliding motor signal (forward)
    Slide switch off
    Below 1 V
    Slide switch front on
    11 to 14 V
    c14-3 (SLD-) - c14-1 (GND)
    P - W-B
    Sliding motor signal (rearward)
    Slide switch off
    Below 1 V
    Slide switch rear on
    11 to 14 V
    c14-6 (FRV+) - c14-1 (GND)
    R - W-B
    Front vertical motor signal (upward)
    Front vertical switch off
    Below 1 V
    Front vertical switch up on
    11 to 14 V
    c14-4 (FRV-) - c14-1 (GND)
    LG - W-B
    Front vertical motor signal (downward)
    Front vertical switch off
    Below 1 V
    Front vertical switch down on
    11 to 14 V
    c14-7 (LFT+) - c14-1 (GND)
    G - W-B
    Lifter motor signal (upward)
    Lifter switch off
    Below 1 V
    Lifter switch up on
    11 to 14 V
    c14-9 (LFT-) - c14-1 (GND)
    W - W-B
    Lifter motor signal (downward)
    Lifter switch off
    Below 1 V
    Lifter switch down on
    11 to 14 V
    c14-8 (RCL+) - c14-1 (GND)
    GR - W-B
    Reclining motor signal (forward)
    Reclining switch off
    Below 1 V
    Reclining switch front on
    11 to 14 V
    c14-10 (RCL-) - c14-1 (GND)
    Y - W-B
    Reclining motor signal (rearward)
    Reclining switch off
    Below 1 V
    Reclining switch rear on
    11 to 14 V
    If the result is not as specified, the position control ECU and switch may have a malfunction.


CHECK POSITION CONTROL ECU AND SWITCH (for RHD)
B107920E25
  1. Disconnect the c26 and c27 switch connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    c26-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    c26-5 (+B) - c26-1 (GND)
    L - W-B
    Power source
    Always
    11 to 14 V
    c27-4 (IG) - c26-1 (GND)
    G - W-B
    Engine switch signal
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V
    c27-8 (SYSB) - c26-1 (GND)
    R - W-B
    System power source
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the c26 and c27 switch connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    c26-2 (SLD+) - c26-1 (GND)
    B - W-B
    Sliding motor signal (forward)
    Slide switch off
    Below 1 V
    Slide switch front on
    11 to 14 V
    c26-3 (SLD-) - c26-1 (GND)
    P - W-B
    Sliding motor signal (rearward)
    Slide switch off
    Below 1 V
    Slide switch rear on
    11 to 14 V
    c26-6 (FRV+) - c26-1 (GND)
    R - W-B
    Front vertical motor signal (upward)
    Front vertical switch off
    Below 1 V
    Front vertical switch up on
    11 to 14 V
    c26-4 (FRV-) - c26-1 (GND)
    LG - W-B
    Front vertical motor signal (downward)
    Front vertical switch off
    Below 1 V
    Front vertical switch down on
    11 to 14 V
    c26-7 (LFT+) - c26-1 (GND)
    G - W-B
    Lifter motor signal (upward)
    Lifter switch off
    Below 1 V
    Lifter switch up on
    11 to 14 V
    c26-9 (LFT-) - c26-1 (GND)
    W - W-B
    Lifter motor signal (downward)
    Lifter switch off
    Below 1 V
    Lifter switch down on
    11 to 14 V
    c26-8 (RCL+) - c26-1 (GND)
    GR - W-B
    Reclining motor signal (forward)
    Reclining switch off
    Below 1 V
    Reclining switch front on
    11 to 14 V
    c26-10 (RCL-) - c26-1 (GND)
    Y - W-B
    Reclining motor signal (rearward)
    Reclining switch off
    Below 1 V
    Reclining switch rear on
    11 to 14 V
    If the result is not as specified, the position control ECU and switch may have a malfunction.


CHECK OUTER MIRROR CONTROL ECU (for LHD)
B179856E01
  1. Disconnect the I17 and I18 ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I18-10 (MSWE) - I17-9 (GND)
    BR - W-B
    Ground for seat memory switch
    Always
    Below 1 Ω
    I17-9 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    I17-3 (B) - I17-9 (GND)
    R - W-B
    Battery (ECU power source)
    Always
    11 to 14 V
    I17-4 (ACC) - I17-9 (GND)
    GR - W-B
    Engine switch (ACC) power source supply
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I17 and I18 ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I18-6 (M3) - I18-10 (MSWE)
    B - BR
    Seat memory switch 3 signal for seat memory switch
    Seat memory switch 3 on
    11 to 14 V
    Seat memory switch 3 off
    Below 1 V
    I18-7 (M2) - I18-10 (MSWE)
    W - BR
    Seat memory switch 2 signal for seat memory switch
    Seat memory switch 2 on
    11 to 14 V
    Seat memory switch 2 off
    Below 1 V
    I18-8 (M1) - I18-10 (MSWE)
    G - BR
    Seat memory switch 1 signal for seat memory switch
    Seat memory switch 1 on
    11 to 14 V
    Seat memory switch 1 off
    Below 1 V
    I18-9 (MM) - I18-10 (MSWE)
    B - BR
    Seat memory SET switch signal for seat memory switch
    Seat memory SET switch on
    11 to 14 V
    Seat memory SET switch off
    Below 1 V
    If the result is not as specified, the outer mirror control ECU may have a malfunction.


CHECK OUTER MIRROR CONTROL ECU (for RHD)
B179856E02
  1. Disconnect the I23 and I24 ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I24-10 (MSWE) - I23-9 (GND)
    BR - W-B
    Ground for seat memory switch
    Always
    Below 1 Ω
    I23-9 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    I23-3 (B) - I23-9 (GND)
    R - W-B
    Battery (ECU power source)
    Always
    11 to 14 V
    I23-4 (ACC) - I23-9 (GND)
    GR - W-B
    Engine switch (ACC) power source supply
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I23 and I24 ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I24-6 (M3) - I24-10 (MSWE)
    B - BR
    Seat memory switch 3 signal for seat memory switch
    Seat memory switch 3 on
    11 to 14 V
    Seat memory switch 3 off
    Below 1 V
    I24-7 (M2) - I24-10 (MSWE)
    W - BR
    Seat memory switch 2 signal for seat memory switch
    Seat memory switch 2 on
    11 to 14 V
    Seat memory switch 2 off
    Below 1 V
    I24-8 (M1) - I24-10 (MSWE)
    G - BR
    Seat memory switch 1 signal for seat memory switch
    Seat memory switch 1 on
    11 to 14 V
    Seat memory switch 1 off
    Below 1 V
    I24-9 (MM) - I24-10 (MSWE)
    B - BR
    Seat memory SET switch signal for seat memory switch
    Seat memory SET switch on
    11 to 14 V
    Seat memory SET switch off
    Below 1 V
    If the result is not as specified, the outer mirror control ECU may have a malfunction.

← PROBLEM SYMPTOMS TABLE (from Jan 2012)DATA LIST / ACTIVE TEST (from Sep 2011) →