P0617 Starter Relay Circuit High
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more |
Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic): (a) Vehicle speed is more than 20 km/h (12.5 mph). (b) Engine speed is more than 1000 rpm. (c) STA signal is on. |
|
| DTC No. |
Data List |
| P0617 |
Starter Signal |
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here).
- If this DTC is output, inspect the starter.
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here).
| 1. READ VALUE USING GTS (STARTER SIGNAL) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / Starter Signal.
Read the value displayed on the GTS when the engine switch is turned on (IG) and when the engine is started.
- OK:
Condition
Starter Signal
Engine switch turned on (IG)
Close
Engine started
Open
|
|
||||
| NG | |
| 2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Inspect the park/neutral position switch assembly (Click here).
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
C45-49 (NSW) - A38-48 (STA)
Always
10 kΩ or higher
C45-49 (NSW) or A38-48 (STA) - Body ground and other terminals
Always
10 kΩ or higher
- Standard Resistance:
for RHD Tester Connection
Condition
Specified Condition
C46-49 (NSW) - A52-48 (STA)
Always
10 kΩ or higher
C46-49 (NSW) or A52-48 (STA) - Body ground and other terminals
Always
10 kΩ or higher
Reconnect the park/neutral position switch assembly connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 4. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 5. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Replace the park/neutral position switch assembly (Click here).
|
|
||||
| 6. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 7. CONFIRM WHETHER DTC OUTPUT RECURS |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the engine switch off.
Turn the engine switch on (IG).
Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
