2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSPECTION

Inspection · Vehicles built from Sep 2011


INSPECT FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)

  1. for Power Seat, for 4 Way Seat Type:
    Check the buckle switch.

    B180619E01

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B-4 - B-5
      Seat belt fastened (Buckle switch is on)
      Below 1 Ω
      Seat belt unfastened (Buckle switch is off)
      1 MΩ or higher
      A-1 - C-4
      Always
      Below 1 Ω
      A-2 - C-8
      Always
      Below 1 Ω

      If the result is not as specified, replace the inner belt assembly.

  1. for 8 Way Seat Type:
    Check the buckle switch.

    B189676E01

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      C-9 - C-13
      Seat belt fastened (Buckle switch is on)
      Below 1 Ω
      Seat belt unfastened (Buckle switch is off)
      1 MΩ or higher
      A-1 - B-4
      Always
      Below 1 Ω
      A-2 - B-8
      Always
      Below 1 Ω

      If the result is not as specified, replace the inner belt assembly.


INSPECT FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)

  1. for Power Seat, w/ Front Seat Side Airbag and Curtain Shield Airbag:
    Check the buckle switch.

    B186708E01

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B-4 - B-5
      Seat belt fastened (Buckle switch is on)
      Below 1 Ω
      Seat belt unfastened (Buckle switch is off)
      1 MΩ or higher
      A-1 - B-4
      Seat belt fastened (Buckle switch is on)
      1 MΩ or higher
      Seat belt unfastened (Buckle switch is off)
      Below 1 Ω
      A-1 - B-4
      Always
      Below 1 Ω
      A-3 - B-3
      Always
      Below 1 Ω

      If the result is not as specified, replace the inner belt assembly.

  1. for Power Seat, w/o Front Seat Side Airbag and Curtain Shield Airbag:
    Check the buckle switch.

    B186709E01

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B-4 - B-5
      Seat belt fastened (Buckle switch is on)
      Below 1 Ω
      Seat belt unfastened (Buckle switch is off)
      1 MΩ or higher
      A-1 - B-4
      Seat belt fastened (Buckle switch is on)
      1 MΩ or higher
      Seat belt unfastened (Buckle switch is off)
      Below 1 Ω
      A-3 - B-3
      Always
      Below 1 Ω

      If the result is not as specified, replace the inner belt assembly.

  1. for Manual Seat:
    Check the buckle switch.

    B187507E01

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B-9 - B-13
      Seat belt fastened (Buckle switch is on)
      Below 1 Ω
      Seat belt unfastened (Buckle switch is off)
      1 MΩ or higher
      A-1 - B-9
      Seat belt fastened (Buckle switch is on)
      1 MΩ or higher
      Seat belt unfastened (Buckle switch is off)
      Below 1 Ω
      A-3 - B-14
      Always
      Below 1 Ω

      If the result is not as specified, replace the inner belt assembly.

← REMOVAL (from Jan 2012)INSTALLATION (Sep 2011 – Dec 2011) →