2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and under cover.


6. REMOVE UPPER RADIATOR SUPPORT SEAL

  1. B180889
    Remove the 7 clips and radiator support seal.


7. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


    A174296E01

  1. Tighten the radiator drain cock plug by hand.


8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
  1. Remove the cowl top ventilator louver (Click here).


9. REMOVE V-BANK COVER

  1. A178931
    Remove the 2 nuts and V-bank cover.


10. REMOVE NO. 2 AIR CLEANER HOSE

  1. A178932
    Loosen the 2 hose clamps and remove the air cleaner hose.


11. REMOVE AIR CLEANER ASSEMBLY

  1. A151812
    Disconnect the No. 2 ventilation hose.

  1. Detach the hose clamp.

  1. A185261
    Disconnect the vacuum hose.

  1. Disconnect the MAF meter connector.

  1. Using a clip remover, detach the 2 wire harness clamps.

  1. A151770
    Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner assembly.


12. REMOVE INTAKE AIR SURGE TANK

  1. A151856
    Disconnect the throttle body connector.

  1. Disconnect the No. 4 water by-pass hose.

  1. Disconnect the No. 5 water by-pass hose.

  1. A178934
    Disconnect the purge line hose.

  1. Disconnect the purge VSV connector.

  1. Disconnect the No. 1 ventilation hose.

  1. A185262
    Disconnect the vacuum switching valve (for ACIS) connector.

  1. Using a clip remover, detach the 2 wire harness clamps.

  1. A151767
    Remove the 2 bolts and throttle body bracket.

  1. A178935
    Using a clip remover, detach the wire harness clamp.

  1. A178936
    Remove the bolt and bracket from the No. 1 surge tank stay.

  1. Remove the bolt and oil baffle plate.

  1. A178937
    Remove the 2 bolts and No. 1 surge tank stay.

  1. A178939
    for Manual Transmission:

    1. Remove the nut.

  1. A178938
    Remove the 2 bolts and No. 2 surge tank stay.

  1. A178940E01
    Remove the 2 nuts.

  1. Using an 8 mm hexagon wrench, remove the 4 bolts. Then remove the intake air surge tank and gasket.


13. REMOVE FUEL PRESSURE PULSATION DAMPER ASSEMBLY

  1. A157496E02
    Remove the fuel pressure regulator holder.

  1. Pull the fuel pressure pulsation damper out of the fuel delivery pipe.

  1. Remove the O-ring from the fuel pressure pulsation damper.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →