2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

PRECAUTION

Precautions · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
  1. Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.
  2. Do not smoke or be near an open flame when working on the fuel system.
  3. Keep gasoline away from rubber and leather parts.


1.IGNITION SWITCH EXPRESSION

HINT:
The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.
Expression
Ignition Switch (Position)
Engine Switch (Condition)
Ignition Switch off
LOCK
Off
Ignition Switch ACC
ACC
On (ACC)
Ignition Switch ON
ON
On (IG)
Engine Start
START
Start


2.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Remove the engine room relay block cover.

  2. A176383E02
    Remove the circuit opening relay (C/OPN).

  3. Start the engine. After the engine has stopped on its own, turn the engine switch off.

    HINT:
    If DTC P0230 is output, clear the DTC (Click here).

  4. Crank the engine, then check that the engine does not start.

  5. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  6. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  7. Install the circuit opening relay (C/OPN).

  8. Install the engine room relay block cover.


3.FUEL SYSTEM

  1. When disconnecting the high fuel pressure line, a large amount of gasoline will spill out. Follow these procedures.

    1. Discharge the fuel system pressure.

    2. A133694
      Put a container under the connecting part of the pressure line.

    3. Slowly loosen the connection.

    4. Disconnect the connection.

    5. Plug the connection with a rubber plug.

  2. A133695E03
    Observe these precautions when removing and installing the injectors:

    NOTICE:
    1. Never reuse the O-ring.
    2. When placing a new O-ring on the injector, do not damage it.
    3. Coat a new O-ring with spindle oil or gasoline before installing it. Do not use engine oil, gear oil or brake oil.

  3. A133696E03
    Install the injector to the delivery pipe and cylinder head as shown in the illustration.

    NOTICE:
    Before installing the injector, apply spindle oil or gasoline on the place where the delivery pipe contacts the O-ring of the injector.

  4. Observe these precautions when disconnecting the fuel tube connector (for quick type A).

    1. A181442E01
      for Fuel Pipe Clamp Type:
      Remove the fuel pipe clamp from the fuel tube connector.

    2. A157617E02
      for Fuel Hose Connector Cover Type:
      Detach the lock claw by lifting up the cover, as shown in the illustration.

    3. Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.

    4. A088336E20
      Pinch the connector and disconnect the connector and pipe.
      If the connector and the pipe are stuck together, pinch the connector, then push and pull the pipe to disconnect the pipe and pull it out.

      NOTICE:
      Do not use any tools in this procedure.

    5. Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.

    6. A099427E11
      To protect the disconnected pipe and connector from damage and contamination, cover it with a plastic bag.

  5. Observe these precautions when disconnecting the fuel tube connector (for quick type B).

    1. A167866E01
      Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.

    2. A091246E02
      Detach the 2 claws of the connector retainer. Push down on the connector and disconnect it from the pipe.

      HINT:
      If the connector and pipe are stuck, pinch the fuel pipe by hand, and push and pull the connector to disconnect it.

      NOTICE:
      Do not use any tools in this procedure.

    3. Check for foreign matter on the seal surface of the disconnected pipe. Clean it if necessary.

    4. A103972E02
      To protect the disconnected pipe and connector from damage and foreign matter, cover it with a plastic bag.

  6. Observe these precautions when connecting the fuel tube connector (for quick type B).

    1. A125397E01
      Check for foreign matter on the pipe and around the connector before connecting it. Clean it if necessary.

    2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector, and push up on the retainer.

    3. A093435
      After connecting the pipe and connector, try to pull them apart to confirm that they are securely connected.

  7. A130944E01
    Observe these precautions when connecting the fuel tube connector (for quick type A).

    1. Check that there is no damage or contamination in the connected part of the pipe.

    2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline on the tip of the pipe.

    3. A130945E02
      After having finished the connection, try to pull apart the pipe and the connector to confirm that they are securely connected.

    4. A157616E01
      for Fuel Hose Connector Cover Type:
      Attach the lock claw to the connector by pushing down on the cover, as shown in the illustration.

    5. A181442E01
      for Fuel Pipe Clamp Type:
      Install the fuel pipe clamp to the connector.

    6. Check that there is no fuel leakage.


4.CHECK FOR FUEL LEAK
  1. Check that there are no fuel leaks after performing maintenance anywhere on the fuel system (Click here).

← REASSEMBLY (from Sep 2011)PRECAUTION (from Jan 2012) →