2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

HINT:
  1. Use the same procedures for LHD and RHD vehicles.
  2. The procedures listed below are for LHD vehicles.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL NO. 2 DISC PLAYER BRACKET

  1. B182283E01
    Align the protrusions of the bracket, labeled A, with the indentations of the navigation module board.

  1. Install the bracket with the 2 screws labeled B.

    Torque:
    3.0 N*m{ 30 kgf*cm , 26 in.*lbf }


2. INSTALL NO. 1 DISC PLAYER BRACKET

  1. B182284E01
    Align the protrusions of the bracket, labeled A, with the indentations of the navigation module board.

  1. Install the bracket with the 2 screws labeled B.

    Torque:
    3.0 N*m{ 30 kgf*cm , 26 in.*lbf }


3. INSTALL NAVIGATION MODULE BOARD WITH DISC PLAYER BRACKET

B182282
  1. Connect the navigation module board connectors.

  1. Install the navigation module board with disc player bracket with the nut and 2 screws.

    Torque:
    Nut:
    12 N*m{ 122 kgf*cm , 8 ft.*lbf }

  1. Attach the clamp.


4. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

B180304
  1. Connect the connector.

  1. Attach the 3 claws to install the lower No. 2 instrument panel finish panel.

  1. Install the 4 bolts.


5. INSTALL INSTRUMENT PANEL BOX DOOR KNOB

B182549
  1. Attach the 2 claws to install the instrument panel box door knob.


6. INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

  1. B189607E01
    Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 4 claws to install the front passenger side knee airbag.

  1. Install the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


7. INSTALL LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

B180302
  1. Attach the 4 claws to install the lower instrument panel.

  1. Install the 2 bolts.


8. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B182552
  1. Attach the 4 claws to install the No. 2 instrument panel under cover.


9. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


10. INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B182550
  1. Attach the 6 claws to install the No. 3 instrument cluster finish panel garnish.


11. INSTALL INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

B186358
  1. Connect the connector.

  1. Attach the 6 claws to install the instrument side panel.


12. INSTALL INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

B182551
  1. Attach the 6 claws to install the instrument side panel.


13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


14. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).

← REMOVAL (Sep 2011 – Dec 2011)PRECAUTION (from Jan 2012) →