Door Courtesy Light Circuit
Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The door courtesy light turns on when the door is opened and turns off when closed.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK OPERATION OF DOOR COURTESY LIGHT |
When a door is opened, check that the following lights do not illuminate.
| Result |
Proceed to |
| All door courtesy light does not illuminate |
A |
| Front door courtesy light LH does not illuminate |
B |
| Front door courtesy light RH does not illuminate |
C |
| Rear door courtesy light LH does not illuminate |
D |
| Rear door courtesy light RH does not illuminate |
E |
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. INSPECT FUSE (DOME1) |
Remove the DOME1 fuse from the engine room junction block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
DOME1 fuse
Always
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (DOOR COURTESY LIGHT - BODY GROUND) |
Disconnect the I13, I5, J12 and J5 ECU connectors.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
I13-1 - Body ground
Always
11 to 14 V
J12-1 - Body ground
I5-1 - Body ground
J5-1 - Body ground
|
|
||||
| OK | ||
| ||
| 4. INSPECT DOOR COURTESY LIGHT (FRONT DOOR LH) |
Remove the door courtesy light connector.

Check that the door courtesy light comes on.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) - Terminal 2
Battery positive (-) - Terminal 1
Light illumination
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND) |
Remove the main body ECU.

for LHD:
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E1-24 (DCTY) - Body ground
Always
11 to 14V
for RHD:
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E2-21 (PCTY) - Body ground
Always
11 to 14V
|
|
||||
| OK | ||
| ||
| 6. INSPECT DOOR COURTESY LIGHT (FRONT DOOR RH) |
Remove the door courtesy light connector.

Check that the door courtesy light comes on.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) - Terminal 2
Battery positive (-) - Terminal 1
Light illumination
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND) |
Remove the main body ECU.

for LHD:
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E2-21 (PCTY) - Body ground
Always
11 to 14V
for RHD:
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E1-24 (DCTY) - Body ground
Always
11 to 14V
|
|
||||
| OK | ||
| ||
| 8. INSPECT COURTESY LIGHT (REAR DOOR LH) |
Remove the door courtesy light connector.

Check that the door courtesy light comes on.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) - Terminal 2
Battery positive (-) - Terminal 1
Light illumination
|
|
||||
| OK | ||
| ||
| 9. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND) |
Remove the main body ECU.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
2C-2 (LCTY) - Body ground
Always
11 to 14V
|
|
||||
| OK | ||
| ||
| 10. INSPECT DOOR COURTESY LIGHT (REAR DOOR RH) |
Remove the door courtesy light connector.

Check that the door courtesy light comes on.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) - Terminal 2
Battery positive (-) - Terminal 1
Light illumination
|
|
||||
| OK | ||
| ||
| 11. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND) |
Remove the main body ECU.

except Double Swing Out Type:
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E2-7 (RCTY) - Body ground
Always
11 to 14V
for Double Swing Out Type:
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E1-17 (RCTY) - Body ground
Always
11 to 14V
|
|
||||
| OK | ||
| ||
