Door Courtesy Switch Circuit
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The main body ECU receives a door open/closed signal from each door courtesy light switch.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY LIGHT SWITCH) |
Using the intelligent tester, read the Data List (Click here).
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door Courtesy SW
Front door courtesy light switch LH signal / ON or OFF
ON: Front door courtesy light switch LH on
OFF: Front door courtesy light switch LH off
-
P Door Courtesy SW
Front door courtesy light switch RH signal / ON or OFF
ON: Front door courtesy light switch RH on
OFF: Front door courtesy light switch RH off
-
RL Door Courtesy SW
Rear door courtesy light switch LH signal / ON or OFF
ON: Rear door courtesy light switch LH on
OFF: Rear door courtesy light switch LH off
-
RR Door Courtesy SW
Rear door courtesy light switch RH signal / ON or OFF
ON: Rear door courtesy light switch RH on
OFF: Rear door courtesy light switch RH off
-
Back Door Courtesy SW
Back door courtesy light switch signal / ON or OFF
ON: Back door courtesy light switch on
OFF: Back door courtesy light switch off
-
- OK:
- Door courtesy light switch on/off
|
|
||||
| OK | ||
| ||
| 2. CHECK DOOR COURTESY LIGHT SWITCH |
| Result |
Proceed to |
| Front door courtesy light switch LH does not operate |
A |
| Front door courtesy light switch RH does not operate |
B |
| Rear door courtesy light switch LH does not operate |
C |
| Rear door courtesy light switch RH does not operate |
D |
| Back door courtesy light switch does not operate |
E |
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 3. INSPECT FRONT DOOR COURTESY LIGHT SWITCH LH |
Remove the front door courtesy light switch LH (Click here).
Inspect the front door courtesy light switch LH (Click here).
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU [COWL SIDE JUNCTION BLOCK LH]) |
Disconnect the K2 front door courtesy light switch LH connector.
for LHD:
Disconnect the E1 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
K2-1 - E1-24 (DCTY)
Always
Below 1 Ω
K2-1 - Body ground
Always
10 kΩ or higher
for RHD:
Disconnect the E2 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
K2-1 - E2-21 (PCTY)
Always
Below 1 Ω
K2-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 5. INSPECT FRONT DOOR COURTESY LIGHT SWITCH RH |
Remove the front door courtesy light switch RH (Click here).
Inspect the front door courtesy light switch RH (Click here).
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU [COWL SIDE JUNCTION BLOCK LH]) |
Disconnect the L1 front door courtesy light switch RH switch connector.
for LHD:
Disconnect the E2 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L1-1 - E2-21 (PCTY)
Always
Below 1 Ω
L1-1 - Body ground
Always
10 kΩ or higher
for RHD:
Disconnect the E1 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L1-1 - E1-24 (DCTY)
Always
Below 1 Ω
L1-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 7. INSPECT REAR DOOR COURTESY LIGHT SWITCH LH |
Remove the rear door courtesy light switch LH (Click here).
Inspect the rear door courtesy light switch LH (Click here).
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU [COWL SIDE JUNCTION BLOCK LH]) |
Disconnect the 2C main body ECU connector.
Disconnect the K3 rear door courtesy light switch LH connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
K3-1 - 2C-2 (LCTY)
Always
Below 1 Ω
K3-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 9. INSPECT REAR DOOR COURTESY LIGHT SWITCH RH |
Remove the rear door courtesy light switch RH (Click here).
Inspect the rear door courtesy light switch RH (Click here).
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU [COWL SIDE JUNCTION BLOCK LH]) |
Disconnect the L2 rear door courtesy light switch RH connector.
except Double Swing Out Type:
Disconnect the E2 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L2-1 - E2-7 (RCTY)
Always
Below 1 Ω
L2-1 - Body ground
Always
10 kΩ or higher
for Double Swing Out Type:
Disconnect the E1 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L2-1 - E1-17 (RCTY)
Always
Below 1 Ω
L2-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 11. INSPECT VEHICLE TYPE |
Check the vehicle type.
Result Result
Proceed to
for Double Swing Out Type
A
except Double Swing Out Type
B
|
|
||||
| A | |
| 12. INSPECT BACK DOOR WITH MOTOR LOCK ASSEMBLY |
Remove the back door with motor lock assembly (Click here).
Inspect the back door with motor lock assembly (Click here).
|
|
||||
| OK | |
| 13. CHECK HARNESS AND CONNECTOR (BACK DOOR WITH MOTOR LOCK ASSEMBLY - MAIN BODY ECU [COWL SIDE JUNCTION BLOCK LH] AND BODY GROUND) |
Disconnect E2 main body ECU connector.
Disconnect W3 back door with motor lock connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
W3-2 (+) - E2-25 (BCTY)
Always
Below 1 Ω
W3-1 (E) - Body ground
W3-2 (+) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 14. INSPECT BACK DOOR LOCK ASSEMBLY |
Remove the back door lock (Click here).
Inspect the back door lock (Click here).
|
|
||||
| OK | |
| 15. CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU [COWL SIDE JUNCTION BLOCK LH] AND BODY GROUND) |
Disconnect the E2 main body ECU connector.
w/o Power Back Door:
Disconnect the S1 back door lock connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S1-3 (+) - E2-25 (BCTY)
Always
Below 1 Ω
S1-1 (ACT-) - Body ground
S1-3 (+) - Body ground
Always
10 kΩ or higher
w/ Power Back Door:
Disconnect the S22 back door lock connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S22-3 (CTY) - E2-25 (BCTY)
Always
Below 1 Ω
S22-4 (E) - Body ground
S22-3 (CTY) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
