2011-2013 Land Cruiser · Service Manual Drivetrain

DATA LIST / ACTIVE TEST

System information · Vehicles built Sep 2011 – Dec 2011


READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Calculate Load
    Calculated load/
    Min.: 0%
    Max.: 100%
    1. Idling: 11 to 25%
    2. Running without load (2500 rpm): 12 to 26%
    -
    Engine Speed
    Engine speed/
    Min.: 0 rpm
    Max.: 16383.75 rpm
    Idling: 650 to 750 rpm
    -
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Actual vehicle speed
    The speed is indicated on the speedometer.
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C (-40°F)
    Max.: 140°C (284°F)
    After warming up: 80 to 100°C (176 to 212°F)
    If the value is -40°C (-40°F), the sensor circuit is open.
    If the value is 140°C (284°F), the sensor circuit is shorted.
    Throttle Position
    Absolute throttle position/
    Min.: 0%
    Max.: 100%
    Throttle is fully
    1. Closed: 10 to 24%
    2. Open: 64 to 96%
    Read the value with the non-intrusive operation (Active Test).
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
    -
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    Lock-up:
    1. ON (after warming up engine): Input turbine speed (NT) equal to engine speed
    2. OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
    The data is displayed in increments of 50 rpm.
    Starter Signal
    Starter signal/
    ON or OFF
    Engine:
    1. ON: Cranking
    2. OFF: Not cranking
    -
    Closed Throttle Position SW
    Closed throttle position switch/
    ON or OFF
    Throttle:
    1. ON: Fully closed
    2. OFF: Open
    -
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In P or N: ON
    2. Not in P or N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Stop Light Switch
    Stop light switch status/
    ON or OFF
    Brake pedal:
    1. Depressed: ON
    2. Released: OFF
    -
    TC and TE1
    TC and TE1 terminals of DLC3/
    ON or OFF
    -
    The Active Test support data.
    Idle Fuel Cut
    Fuel cut idle/
    ON or OFF
    Fuel cut:
    1. ON: Operating
    2. OFF: Not operating
    Idle Fuel Cut is "ON" when the throttle valve is fully closed and the engine speed is more than 2800 rpm.
    FC TAU
    Fuel cut TAU (Fuel cut during very light load)/
    ON or OFF
    Fuel cut:
    1. ON: Operating
    2. OFF: Not operating
    Fuel cut is being performed under a very light load to prevent the engine combustion from becoming incomplete.
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th or 5th
    Shift lever:
    1. In D: 1st, 2nd, 3rd, 4th or 5th
    2. In S: 1st, 2nd, 3rd, 4th or 5th
    -
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In R: ON
    2. Not in R: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (P Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In P: ON
    2. Not in P: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (N Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In N: ON
    2. Not in N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    Shift lever:
    1. In D: ON
    2. Not in D: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Shift lever held in "+" (up-shift)
    2. OFF: Shift lever not in "+" (up-shift)
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Shift lever held in "-" (down-shift)
    2. OFF: Shift lever not in "-" (down-shift)
    -
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    Shift lever is:
    1. ON: In S, "+" or "-"
    2. OFF: Not in S, "+" or "-"
    -
    Pattern Switch (PWR/M)
    Pattern switch (PWR) status/
    ON or OFF
    Pattern switch (PWR):
    1. Pushed: ON
    2. Not pushed: OFF
    -
    Snow Switch Status
    Pattern switch (2ND) status/
    ON or OFF
    Pattern switch (2ND):
    Pushed: ON
    ↓
    Pattern switch (2ND):
    Pushed: OFF
    -
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. With engine cold: Equal to ambient temperature
    If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.
    A/T Oil Temperature 2
    No. 2 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. With engine cold: Equal to ambient temperature
    If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted.
    AT Fluid
    Flex lock-up judder judgment/
    ON or OFF
    1. ON: Judder judgment occurs
    2. OFF: Judder judgment does not occur
    -
    Lock Up
    Lock-up/
    ON or OFF
    Lock-up:
    1. Operating: ON
    2. Not operating: OFF
    -
    Lock Up Solenoid Status
    Lock-up solenoid status/
    ON or OFF
    Lock-up solenoid:
    1. Operating: ON
    2. Not operating: OFF
    -
    SLU Solenoid Status
    Shift solenoid valve SLU status/
    ON or OFF
    Shift solenoid valve SLU:
    1. Operating: ON
    2. Not operating: OFF
    -
    SLT Solenoid Status
    Shift solenoid valve SLT status/
    ON or OFF
    1. Accelerator pedal depressed: OFF
    2. Accelerator pedal is released: ON
    -
    Engine Speed from EFI
    Engine speed/
    Min.: 0 rpm
    Max.: 16383.75 rpm
    Idling: 650 to 750 rpm
    The engine speed received from the ECM.
    Intake-Air Temp from EFI
    Intake air temperature/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    Equivalent to ambient air temperature
    The intake air temperature received from the ECM.
    Coolant Temp from EFI
    Engine coolant temperature/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    After warming up: 80 to 100°C (176 to 212°F)
    The coolant temperature received from the ECM.
    Throttle Position from EFI
    Throttle sensor positioning/
    Min.: 0%
    Max.: 100%
    Idling: 0 to 10%
    The throttle position received from the ECM.
    Accel Position from EFI
    Accelerator sensor positioning/
    Min.: 0%
    Max.: 100%
    Idling: 0 to 10%
    The accelerator position received from the ECM.
    # Codes
    # of Codes/
    Min.: 0
    Max.: 255
    -
    The number of stored DTCs.
    MIL ON Run Distance
    MIL on run distance/
    Min.: 0 km (0 mile)
    Max.: 65535 km (40723 mile)
    Distance after DTC stored
    -
    Running Time from MIL ON
    Running time from MIL on/
    Min.: 0 minutes
    Max.: 65535 minutes
    Equivalent to running time after MIL is on
    -
    Engine Run Time
    Engine run time/
    Min.: 0 seconds
    Max.: 65535 seconds
    Time after engine start
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Active Test.

  7. According to the display on the tester, perform the Active Test.

    ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON or OFF
    1. ON: TC and TE1 are connected.
    2. OFF: TC and TE1 are disconnected.
    Activate the Solenoid (SLU)
    Operate shift solenoid valve SLU
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.
    Activate the Solenoid (SLT)*
    Operate shift solenoid valve SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands shift solenoid valve SLT to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. The vehicle is stopped.
    2. The engine is idling.
    Activate the Solenoid (S1)
    Operate shift solenoid valve S1
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.
    Activate the Solenoid (S2)
    Operate shift solenoid valve S2
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.
    Activate the Lock Up
    Control shift solenoid valve SLU to set automatic transmission to lock-up condition
    ON or OFF
    It is possible to check the shift solenoid valve SLU operation.
    [Vehicle Condition]
    1. The throttle valve opening angle is less than 35%.
    2. The vehicle speed is 60 km/h (37 mph) or more.
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    It is possible to check the operation of the shift solenoid valves.
    [Vehicle Condition]
    The vehicle speed is 50 km/h (31 mph) or less.
    Activate the Solenoid (SR)
    Operate shift solenoid valve SR
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.
    Activate the Solenoid (SL1)
    Operate shift solenoid valve SL1
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.
    Activate the Solenoid (SL2)
    Operate shift solenoid valve SL2
    ON or OFF
    [Vehicle Condition]
    1. The engine is stopped.
    2. The shift lever is in P or N.

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and hydraulic test are different.

← FAIL-SAFE CHART (Sep 2011 – Dec 2011)DIAGNOSTIC TROUBLE CODE CHART (Sep 2011 – Dec 2011) →