P0717 Turbine Speed Sensor Circuit No Signal
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
This sensor detects the rotation speed of the turbine which shows the input revolution of the transmission. By comparing the input turbine speed signal NT with the counter gear speed sensor signal SP2, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0717 |
All the conditions below are detected for 5 sec. or more (1 trip detection logic). (a) Gear change is not performed. (b) The gear position is 4th, 5th or 6th. (c) The T/M input shaft rpm is 300 rpm or less. (d) The T/M output shaft rpm is 1000 rpm or more. (e) The park/neutral position switch:
|
|
Check the waveform of the ECM connector.
- Standard:
for LHD Terminal No. (Symbol)
Tool Setting
Condition
Specified Condition
C45-76 (NT+) - C45-75 (NT-)
1 V/DIV., 2 msec./DIV.
Engine idling (shift lever in P or N)
Refer to illustration
for RHD Terminal No. (Symbol)
Tool Setting
Condition
Specified Condition
C46-76 (NT+) - C46-75 (NT-)
1 V/DIV., 2 msec./DIV.
Engine idling (shift lever in P or N)
Refer to illustration


MONITOR DESCRIPTION
This DTC indicates that a pulse is not output from the speed sensor NT (turbine (input) speed sensor) or is output only a little. The NT terminal of the ECM detects the pulse signal from the speed sensor NT (input RPM). The ECM outputs a gear shift signal comparing the input speed sensor NT with the output speed sensor SP2.While the vehicle is operating in the 4th, 5th or 6th gear position with the shift lever in D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is 1000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.
- HINT:
- *1: Pulse is not output or is irregularly output.
- *2: The vehicle speed is approximately 50 km/h (31 mph) or more.
- *1: Pulse is not output or is irregularly output.
WIRING DIAGRAM


INSPECTION PROCEDURE
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
SPD (NT)
Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
Lock-up: - ON (after warming up engine): Input turbine speed (NT) equal to engine speed
- OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
The data is displayed in increments of 50 rpm.
- HINT:
- SPD (NT) is always 0 while driving:
Open or short in the sensor or circuit.
- SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
Sensor trouble, improper installation, or intermittent connection trouble of the circuit.
- SPD (NT) is always 0 while driving:
- ON (after warming up engine): Input turbine speed (NT) equal to engine speed
| 1. INSPECT SPEED SENSOR NT INSTALLATION |
Check the speed sensor NT installation.

- OK:
- The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
Text in Illustration *a
CORRECT
*b
INCORRECT
|
|
||||
| OK | |
| 2. INSPECT SPEED SENSOR NT |
Disconnect the speed sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
560 to 680 Ω
Text in Illustration *a
Component without harness connected
(Speed Sensor NT)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM) |
Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
C45-76 (NT+) - C45-75 (NT-)
20°C (68°F)
560 to 680 Ω
C45-76 (NT+) - Body ground
Always
10 kΩ or higher
C45-75 (NT-) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
C46-76 (NT+) - C46-75 (NT-)
20°C (68°F)
560 to 680 Ω
C46-76 (NT+) - Body ground
Always
10 kΩ or higher
C46-75 (NT-) - Body ground
Always
10 kΩ or higher
| *1 |
for LHD |
| *2 |
for RHD |
| *a |
Front view of wire harness connector (to ECM) |
|
|
||||
| OK | ||
| ||
