2011-2013 Land Cruiser · Service Manual Drivetrain

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.
DTC Code
DTC Detection Condition
Trouble Area
P0705
One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic):
  1. P input signal
  2. N input signal
  3. R input signal
  4. D input signal
(B) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic):
  1. NSW input signal
  2. R input signal
  3. D input signal
(C) Any of following signals are ON for 2.0 seconds or more in S position (2 trip detection logic):
  1. NSW input signal
  2. P input signal
  3. N input signal
  4. R input signal
(D) P, R, N and D switches are OFF simultaneously (2 trip detection logic).
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. Transmission control switch (lower shift lever assembly)
  4. ECM

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or S).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C177781E17

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the intelligent tester, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. In P or N: ON
    2. Not in P or N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (P Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. In P: ON
    2. Not in P: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. In R: ON
    2. Not in R: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (N Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. In N: ON
    2. Not in N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Continuously shift to "+" (up-shift)
    2. OFF: Release "+" (up-shift)
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Continuously shift to "-" (down-shift)
    2. OFF: Release "-" (down-shift)
    -
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    Shift lever position is:
    1. ON: In S, "+" and "-"
    2. OFF: Not in S, "+" and "-"
    -
    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. In D, S, "+" and "-": ON
    2. Not in D, S, "+" and "-": OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.


1. INSPECT TRANSMISSION CONTROL SWITCH

  1. C203344E19
    Disconnect the transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IG) - 7 (S)
    Shift lever in S, "+" or "-"
    Below 1 Ω
    3 (IG) - 7 (S)
    Shift lever not in S, "+" or "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch)



NG
REPLACE TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY) (Click here)
OK


2. CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)

  1. C203343E35
    Disconnect the transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E52-3 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V
    E52-3 (IG) - Body ground
    Engine switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transmission Control Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY)
OK


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C197712E28
    Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1. 2 (RB) - 6 (PL)
    2. 4 (B) - 5 (L)
    Shift lever in P
    Below 1 Ω
    2 (RB) - 1 (RL)
    Shift lever in R
    Below 1 Ω
    1. 2 (RB) - 9 (NL)
    2. 4 (B) - 5 (L)
    Shift lever in N
    Below 1 Ω
    2 (RB) - 7 (DL)
    Shift lever in D, S, "+" or "-"
    Below 1 Ω
    1. 2 (RB) - 6 (PL)
    2. 4 (B) - 5 (L)
    Shift lever not in P
    10 kΩ or higher
    2 (RB) - 1 (RL)
    Shift lever not in R
    10 kΩ or higher
    1. 2 (RB) - 9 (NL)
    2. 4 (B) - 5 (L)
    Shift lever not in N
    10 kΩ or higher
    2 (RB) - 7 (DL)
    Shift lever not in D, S, "+" or "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


4. CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)

  1. C197711E49
    Disconnect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C24-2 (RB) - Body ground
    Engine switch on (IG)
    11 to 14 V
    C24-2 (RB) - Body ground
    Engine switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BATTERY)
OK


5. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

  1. C219456E15
    Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C45-2 (P) - Body ground
    1. Engine switch on (IG)
    2. Shift lever in P
    11 to 14 V
    C45-26 (R) - Body ground
    1. Engine switch on (IG)
    2. Shift lever in R
    11 to 14 V*
    C45-25 (N) - Body ground
    1. Engine switch on (IG)
    2. Shift lever in N
    11 to 14 V
    C45-27 (D) - Body ground
    1. Engine switch on (IG)
    2. Shift lever in D
    11 to 14 V
    C45-120 (NSW) - Body ground
    1. Engine switch on (IG)
    2. Shift lever not in P or N
    11 to 14 V
    C45-2 (P) - Body ground
    1. Engine switch on (IG)
    2. Shift lever not in P
    Below 1 V
    C45-26 (R) - Body ground
    1. Engine switch on (IG)
    2. Shift lever not in R
    Below 1 V
    C45-25 (N) - Body ground
    1. Engine switch on (IG)
    2. Shift lever not in N
    Below 1 V
    C45-27 (D) - Body ground
    1. Engine switch on (IG)
    2. Shift lever not in D
    Below 1 V
    C45-120 (NSW) - Body ground
    1. Engine switch on (IG)
    2. Shift lever in P or N
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

    HINT:
    *: The voltage will drop slightly due to turning on the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

  1. C197708E42
    Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A38-25 (S) - Body ground
    1. Engine switch on (IG)
    2. Shift lever in S, "+" and "-"
    11 to 14 V
    A38-25 (S) - Body ground
    1. Engine switch on (IG)
    2. Shift lever not in S, "+" and "-"
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (Sep 2011 – Dec 2011)P0710 Transmission Fluid Temperature Sensor "A" Circuit (+ P0712, P0713) (Sep 2011 – Dec 2011) →