2011-2013 Land Cruiser · Service Manual Drivetrain

P0710 Transmission Fluid Temperature Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The Automatic Transmission Fluid (ATF) temperature sensor converts the fluid temperature into a resistance value which is input into the ECM.
C146747E01
The ECM applies a voltage to the temperature sensor through the ECM terminal THO1.
The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.
The ECM calculates the fluid temperature based on the voltage signal.
w/ OBD 
DTC Code
DTC Detection Condition
Trouble Area
P0712
The No. 1 ATF temperature sensor resistance is below 79 Ω for 0.5 seconds or more (1 trip detection logic).
  1. Short in No. 1 ATF temperature sensor circuit
  2. No. 1 transmission wire (No. 1 ATF temperature sensor)
  3. ECM
P0713
The No. 1 ATF temperature sensor resistance is higher than 156 kΩ for 0.5 seconds or more, and one of the following conditions is met (1 trip detection logic).
Condition A:
15 minutes or more have elapsed.
Condition B:
If the conditions needed to detect DTC P0711 have been met, P0713 can be detected immediately following engine start.
  1. Open in No. 1 ATF temperature sensor circuit
  2. No. 1 transmission wire (No. 1 ATF temperature sensor)
  3. ECM
w/o OBD 
DTC Code
DTC Detection Condition
Trouble Area
P0710
(a) and (b) are detected momentarily within 0.5 sec. when neither P0712 nor P0713 are stored (1 trip detection logic).
(a) The No. 1 ATF temperature sensor resistance is below 79 Ω.
(b) The No. 1 ATF temperature sensor resistance is higher than 156 kΩ.

HINT:
Within 0.5 sec., the malfunction switches from (a) to (b) or from (b) to (a).

  1. Open or short in No. 1 ATF temperature sensor circuit
  2. Transmission wire (No. 1 ATF temperature sensor)
  3. ECM
P0712
The No. 1 ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1 trip detection logic).
  1. Short in No. 1 ATF temperature sensor circuit
  2. Transmission wire (No. 1 ATF temperature sensor)
  3. ECM
P0713
When 15 min. or more have elapsed after the engine is started, the No. 1 ATF temperature sensor resistance is higher than 156 kΩ for 0.5 sec. or more (1 trip detection logic).
  1. Open in No. 1 ATF temperature sensor circuit
  2. Transmission wire (No. 1 ATF temperature sensor)
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the Automatic Transmission Fluid (ATF) temperature sensor circuit. The ATF temperature sensor converts ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and the ECM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is below 79 Ω*1 or higher than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or wiring. The ECM will turn on the MIL and store the DTC.

HINT:
  1. *1: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.
  2. *2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.
  3. The ATF temperature can be checked on the intelligent tester display.


WIRING DIAGRAM

C155188E05

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the tester, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. With engine cold: Equal to ambient temperature
    If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.

    HINT:
    When DTC P0712 is stored and the intelligent tester output is 150°C (302°F) or higher, there is a short circuit.
    When DTC P0713 is stored and the intelligent tester output is -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the tester in order to check if a malfunction exists.

    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or higher
    Short circuit


1. INSPECT TRANSMISSION WIRE (NO. 1 ATF TEMPERATURE SENSOR)

  1. C159421E01
    Disconnect the C34 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (OT-) - 10 (OT+)
    Always
    79 Ω to 156 kΩ
    2 (OT-) - Body ground
    Always
    10 kΩ or higher
    10 (OT+) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range of one of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

    Resistance (Reference):
    ATF Temperature
    Specified Condition
    10°C (50°F)
    5 to 8 kΩ
    25°C (77°F)
    2.5 to 4.5 kΩ
    110°C (230°F)
    0.22 to 0.28 kΩ



NG
REPAIR OR REPLACE NO. 1 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE) (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C159422E49
    Disconnect the C45 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C45-126 (THO1) - C45-78 (ETHW)
    Always
    79 Ω to 156 kΩ
    C45-126 (THO1) - Body ground
    Always
    10 kΩ or higher
    C45-78 (ETHW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (from Jan 2012)P0711 Transmission Fluid Temperature Sensor "A" Performance (Sep 2011 – Dec 2011) →