2011-2013 Land Cruiser · Service Manual Drivetrain

P0724 Brake Switch "B" Circuit High

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.
DTC Code
DTC Detection Condition
Trouble Area
P0724
The stop light switch remains on even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO (30 km/h (19 mph) or more) pattern 5 times (2 trip detection logic).
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during "stop and go" driving, the ECM interprets this as a fault in the stop light switch, the MIL comes on and the ECM stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) five times for 2 driving cycles in order to detect a malfunction.

WIRING DIAGRAM

C146704E11

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch
    Stop light switch status/
    ON or OFF
    Brake pedal:
    1. Depressed: ON
    2. Released: OFF
    -


1. INSPECT STOP LIGHT SWITCH

  1. C171632E01
    Remove the stop light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    3 - 4
    Pin pushed
    Below 1 Ω
    1 - 2
    Pin pushed
    10 kΩ or higher
    3 - 4
    Pin not pushed
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (BATTERY - ECM)

  1. C177782E10
    Disconnect the A38 ECM connector (for LHD).

  1. Disconnect the A52 ECM connector (for RHD).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A38-36 (STP) - Body ground
    Brake pedal depressed
    11 to 14 V
    A38-36 (STP) - Body ground
    Brake pedal released
    Below 1 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A52-36 (STP) - Body ground
    Brake pedal depressed
    11 to 14 V
    A52-36 (STP) - Body ground
    Brake pedal released
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0722 Output Speed Sensor Circuit No Signal (from Jan 2012)P0724 Brake Switch "B" Circuit High (from Jan 2012) →