2011-2013 Land Cruiser · Service Manual Drivetrain

P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The amount of current flow to the solenoid is controlled by the duty ratio* of the ECM output signal. During the lock-up operation, if the duty ratio increases, the lock-up hydraulic pressure increases.
C159072E01

HINT:
*: The duty ratio is the ratio of the current ON time (A) to the total of the current ON and OFF time (A + B). Duty Ratio (%) = A / (A + B) x 100

DTC Code
DTC Detection Condition
Trouble Area
P2759
An open or short is detected in the shift solenoid valve SLU circuit for 1 sec. or more while driving (1 trip detection logic).
  1. Open or short in shift solenoid valve SLU circuit
  2. Shift solenoid valve SLU
  3. ECM

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve (SLU) circuit is detected, the ECM determines there is a malfunction. The ECM will turn on the MIL and store this DTC.

WIRING DIAGRAM

C178085E05

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)

  1. C159421E09
    Disconnect the C34 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    13 (SLU+) - 5 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    13 (SLU+) - Body ground
    Always
    10 kΩ or higher
    5 (SLU-) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C177486E12
    Disconnect the C45 ECM connector (for LHD).

  1. Disconnect the C46 ECM connector (for RHD).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C45-10 (SLU+) - C45-11 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    C45-10 (SLU+) - Body ground
    Always
    10 kΩ or higher
    C45-11 (SLU-) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C46-10 (SLU+) - C46-11 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    C46-10 (SLU+) - Body ground
    Always
    10 kΩ or higher
    C46-11 (SLU-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

3. INSPECT SHIFT SOLENOID VALVE SLU

  1. C162477E02
    Remove the shift solenoid valve SLU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    Valve moves and makes an operating noise



NG
REPLACE SHIFT SOLENOID VALVE SLU (Click here)
OK

REPAIR OR REPLACE TRANSMISSION WIRE (Click here)


← P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) (Sep 2011 – Dec 2011)P2772 Four Wheel Drive (4WD) Low Switch Circuit Range / Performance (Sep 2011 – Dec 2011) →