2011-2013 Land Cruiser · Service Manual Drivetrain

P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)

Diagnostic trouble codes · Vehicles built from Jan 2012

DESCRIPTION

The amount of current flow to the solenoid is controlled by the ECM. During the lock-up operation, if the current increases, the lock-up hydraulic pressure increases.
C221407E01
DTC Code
DTC Detection Condition
Trouble Area
P2759
An open or short is detected in the shift solenoid valve SLU circuit for 1 sec. or more while driving (1 trip detection logic).
  1. Open or short in shift solenoid valve SLU circuit
  2. Shift solenoid valve SLU
  3. ECM

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLU circuit is detected, the ECM determines that there is a malfunction. The ECM will illuminate the MIL and store this DTC.

WIRING DIAGRAM

C178085E17

INSPECTION PROCEDURE


1. INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)

  1. C214326E40
    Disconnect the No. 1 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    12 (SLU+) - 4 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    12 (SLU+) - Body ground
    Always
    10 kΩ or higher
    4 (SLU-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (No. 1 Transmission Wire)



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
C219456E58
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C45-10 (SLU+) - C45-11 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    C45-10 (SLU+) - Body ground
    Always
    10 kΩ or higher
    C45-11 (SLU-) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C46-10 (SLU+) - C46-11 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    C46-10 (SLU+) - Body ground
    Always
    10 kΩ or higher
    C46-11 (SLU-) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*1
for LHD
*2
for RHD
*a
Front view of wire harness connector
(to ECM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

3. INSPECT SHIFT SOLENOID VALVE SLU

  1. C209928E04
    Remove shift solenoid valve SLU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SLU)


NG
REPLACE SHIFT SOLENOID VALVE SLU (Click here)
OK

REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE (Click here)


← P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) (from Jan 2012)P2772 Four Wheel Drive (4WD) Low Switch Circuit Range / Performance (from Jan 2012) →