2011-2013 Land Cruiser · Service Manual Drivetrain

P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

Refer to DTC P0894 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
P2716
An open or short is detected in the shift solenoid valve SLT circuit for 1 sec. or more while driving (1 trip detection logic).
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. ECM

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C178085E03

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)

  1. C159421E07
    Disconnect the C34 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    14 (SLT+) - 6 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    14 (SLT+) - Body ground
    Always
    10 kΩ or higher
    6 (SLT-) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C177486E10
    Disconnect the C45 ECM connector (for LHD).

  1. Disconnect the C46 ECM connector (for RHD).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C45-9 (SLT+) - C45-8 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    C45-9 (SLT+) - Body ground
    Always
    10 kΩ or higher
    C45-8 (SLT-) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C46-9 (SLT+) - C46-8 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    C46-9 (SLT+) - Body ground
    Always
    10 kΩ or higher
    C46-8 (SLT-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

3. INSPECT SHIFT SOLENOID VALVE SLT

  1. C162477E01
    Remove the shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 2
    2. Battery negative (-) → Terminal 1
    Valve moves and makes an operating noise



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK

REPAIR OR REPLACE TRANSMISSION WIRE (Click here)


← P0985 Shift Solenoid "E" Control Circuit Low (Shift Solenoid Valve SR) (+ P0986) (Sep 2011 – Dec 2011)P2740 Transmission Fluid Temperature Sensor "B" Circuit (+ P2742, P2743) (Sep 2011 – Dec 2011) →