2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0340 Camshaft Position Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The intake camshaft Variable Valve Timing (VVT) sensor (VV1, 2 signal) consists of a magnet and MRE (Magnetic Resistance Element).
The intake camshaft has 3 teeth on its outer circumference. When the intake camshaft rotates, changes occur in the air gaps between the teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the intake camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
The crankshaft position sensor plate has 34 teeth. The crankshaft position sensor generates 34 signals for each revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.
DTC Code
DTC Detection Condition
Trouble Area
P0340
P0345
When either condition below is met:
  1. The input voltage to the ECM remains at below 0.3 V or higher than 4.7 V for 4 seconds when 2 or more seconds have elapsed after turning the engine switch on (IG) (1 trip detection logic).
  2. No VVT sensor (for intake side of Bank 1, 2) signal is sent to the ECM during cranking (2 trip detection logic).
  1. Open or short in VVT sensor (for intake side) circuit
  2. VVT sensor (for intake side)
  3. Intake camshaft (for Bank 1, 2)
  4. Jumped tooth of timing chain
  5. ECM
P0342
P0347
The output voltage of the VVT sensor (for intake side of Bank 1, 2) is below 0.3 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for intake side) circuit
  2. VVT sensor (for intake side)
  3. Intake camshaft (for Bank 1, 2)
  4. Jumped tooth of timing chain
  5. ECM
P0343
P0348
The output voltage of the VVT sensor (for intake side of Bank 1, 2) is higher than 4.7 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for intake side) circuit
  2. VVT sensor (for intake side)
  3. Intake camshaft (for Bank 1, 2)
  4. Jumped tooth of timing chain
  5. ECM

  1. A149748E02
    Reference: Inspection using an oscilloscope

    Standard:
    Tester Connection
    Tool Setting
    Condition
    Specified Condition
    C45-110 (NE+) - C45-111 (NE-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown
    C45-92 (VV1+) - C45-91 (VV1-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown
    C45-87 (VV2+) - C45-88 (VV2-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown

    HINT:
    VV1+ and VV2+ stand for the VVT sensor (for intake side) signal, and NE+ stands for the CKP sensor signal.


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

A179606E09

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.


1. CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
A241165E03
  1. Disconnect the C100 or C101 VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C100-3 (VC) - Body ground
    Engine switch on (IG)
    4.5 to 5.0 V
    C101-3 (VC) - Body ground
    Engine switch on (IG)
    4.5 to 5.0 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE SIDE - ECM)

  1. A182257E12
    Disconnect the C100 or C101 VVT sensor connector.

  1. Disconnect the C45 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C100-1 (VVL+) - C45-92 (VV1+)
    Always
    Below 1 Ω
    C100-2 (VVL-) - C45-91 (VV1-)
    Always
    Below 1 Ω
    C101-1 (VVR+) - C45-87 (VV2+)
    Always
    Below 1 Ω
    C101-2 (VVR-) - C45-88 (VV2-)
    Always
    Below 1 Ω
    C100-1 (VVL+) or C45-92 (VV1+) - Body ground
    Always
    10 kΩ or higher
    C100-2 (VVL-) or C45-91 (VV1-) - Body ground
    Always
    10 kΩ or higher
    C101-1 (VVR+) or C45-87 (VV2+) - Body ground
    Always
    10 kΩ or higher
    C101-2 (VVR-) or C45-88 (VV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK SENSOR INSTALLATION

  1. BR03795E17
    Check the VVT sensor (for intake side) installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4. CHECK INTAKE CAMSHAFT (TEETH)
  1. Check the teeth of the camshaft.

    OK:
    Teeth do not have any cracks or deformation.



NG
REPLACE INTAKE CAMSHAFT (Click here)
OK


5. REPLACE VVT SENSOR (for Intake Side)
  1. Replace the VVT sensor (for Intake Side) (Click here).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Clear DTCs.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    No output
    A
    P0340, P0342, P0343, P0345, P0347 or P0348
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0340 Camshaft Position Sensor Circuit Malfunction (+ 5 more codes) (Sep 2011 – Dec 2011)P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 7 more codes) (Sep 2011 – Dec 2011) →