2011-2013 Land Cruiser · Service Manual Drivetrain

Transmission Control Switch Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When moving the shift lever to S using the transmission control switch, it is possible to switch the shift range between "1" (1st range) and "6" (6th range).
Shifting to "+" once raises the shift range by one, and shifting to "-" lowers the shift range by one.

WIRING DIAGRAM

C176192E19

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION CONTROL SWITCH

  1. C146679E06
    Disconnect the transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IG) - 7 (S)
    Shift lever in S, "+" or "-"
    Below 1 Ω
    2 (SFTU) - 5 (E)
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    1 (SFTD) - 5 (E)
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    3 (IG) - 7 (S)
    Shift lever not in S, "+" or "-"
    10 kΩ or higher
    2 (SFTU) - 5 (E)
    Shift lever in S
    10 kΩ or higher
    1 (SFTD) - 5 (E)
    Shift lever in S
    10 kΩ or higher



NG
REPLACE TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY) (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)

  1. C146729E14
    Disconnect the transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E52-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    E52-3 (IG) - Body ground
    Ignition switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E52-5 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

  1. C177782E14
    Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A38-25 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever in S, "+" or "-"
    11 to 14 V
    A38-25 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever not in S, "+" or "-"
    Below 1 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A52-25 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever in S, "+" or "-"
    11 to 14 V
    A52-25 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever not in S, "+" or "-"
    Below 1 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A38-60 (SFTU) - Body ground
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    A38-59 (SFTD) - Body ground
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    A38-60 (SFTU) - Body ground
    Shift lever in S
    10 kΩ or higher
    A38-59 (SFTD) - Body ground
    Shift lever in S
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A52-60 (SFTU) - Body ground
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    A52-59 (SFTD) - Body ground
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    A52-60 (SFTU) - Body ground
    Shift lever in S
    10 kΩ or higher
    A52-59 (SFTD) - Body ground
    Shift lever in S
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Transmission Control Switch Circuit (Sep 2011 – Dec 2011)Pattern Select Switch Power Mode Circuit (Sep 2011 – Dec 2011) →