2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

MIL Circuit

Circuit diagnosis · Vehicles built from Jan 2012

DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the engine switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.
The MIL operation can be checked visually. When the engine switch is first turned on (IG), the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A182518E01

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. CHECK THAT MIL IS ILLUMINATED
  1. Perform troubleshooting in accordance with the table below.

    Result 
    Condition
    Proceed to
    MIL remains on
    A
    MIL does not illuminate
    B



B
Go to step 5
A


2. CHECK WHETHER MIL TURNS OFF
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Check if DTCs have been stored (Click here). If DTCs are present, write them down.

  1. Clear DTCs (Click here).

  1. Check that the MIL turns off.

    Standard:
    MIL turns off.



NG
Go to step 3
OK

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
A182543E01
  1. Disconnect the ECM connector.

  1. Turn the engine switch on (IG).

  1. Check that the MIL is not illuminated.

    OK:
    MIL is not illuminated.

  1. Reconnect the ECM connector.



NG
Go to step 4
OK

REPLACE ECM

4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
A276482E01
  1. Disconnect the ECM connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    E8-12 (CHK) - A38-24 (W)
    Always
    Below 1 Ω
    E8-12 (CHK) or A38-24 (W) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    E8-12 (CHK) - A52-24 (W)
    Always
    Below 1 Ω
    E8-12 (CHK) or A52-24 (W) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the combination meter connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

5. CHECK THAT MIL IS ILLUMINATED
  1. Check if the MIL is illuminated when the engine switch is turned on (IG).

    OK:
    MIL is illuminated.



NG
Go to step 6
OK

SYSTEM OK

6. CHECK THAT ENGINE STARTS
  1. Turn the engine switch on (IG).

  1. Start the engine.

    Result 
    Result
    Proceed to
    Engine starts
    A
    Engine does not start*
    B

    HINT:
    *: The GTS cannot communicate with the ECM.



B
GO TO VC OUTPUT CIRCUIT (Click here)
A


7. INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)
  1. See the combination meter troubleshooting procedure (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Brake Override System (from Jan 2012)PRECAUTION (from Sep 2011) →