2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

VC Output Circuit

Circuit diagnosis · Vehicles built from Jan 2012

DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
A116143E68
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the engine switch is first turned on (IG). The MIL goes off when the engine is started.


WIRING DIAGRAM

A165964E07
A275261E01
A275262E01
A165964E08
A275261E02
A275262E02

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the engine switch on (IG).

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
END
B


2. CHECK COMMUNICATION BETWEEN GTS AND ECM
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and GTS on.

  1. Check the communication between the GTS and ECM.

    Result 
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3. CHECK MIL (THROTTLE POSITION SENSOR (for Bank 1))
  1. Disconnect the C83 throttle position sensor (for Bank 1) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the C83 throttle position sensor (for Bank 1) connector.



A
REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1) (Click here)
B


4. CHECK MIL (THROTTLE POSITION SENSOR (for Bank 2))
  1. Disconnect the C84 throttle position sensor (for Bank 2) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the C84 throttle position sensor (for Bank 2) connector.



A
REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 2) (Click here)
B


5. CHECK MIL (NO. 1 EGR VALVE POSITION SENSOR)
  1. Disconnect the C87 No. 1 EGR valve connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the C87 No. 1 EGR valve connector.



A
REPLACE NO. 1 EGR VALVE ASSEMBLY (Click here)
B


6. CHECK MIL (NO. 2 EGR VALVE POSITION SENSOR)
  1. Disconnect the C88 No. 2 EGR valve connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the C88 No. 2 EGR valve connector.



A
REPLACE NO. 2 EGR VALVE ASSEMBLY (Click here)
B


7. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the A31 accelerator pedal position sensor connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the A31 accelerator pedal position sensor connector.



A
REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (Click here)
B


8. CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Disconnect the C80 manifold absolute pressure sensor connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the C80 manifold absolute pressure sensor connector.



A
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR (Click here)
B


9. CHECK MIL (FUEL PRESSURE SENSOR)
  1. Disconnect the C82 fuel pressure sensor connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the C82 fuel pressure sensor connector.



A
REPLACE COMMON RAIL (for Bank 1) (Click here)
B


10. CHECK MIL (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY (for Bank 1))
  1. Disconnect the N16 differential pressure sensor assembly (for Bank 1) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the N16 differential pressure sensor assembly (for Bank 1) connector.



A
REPLACE DIFFERENTIAL PRESSURE SENSOR (for Bank 1) (Click here)
B


11. CHECK MIL (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY (for Bank 2))
  1. Disconnect the C157 differential pressure sensor assembly (for Bank 2) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the C157 differential pressure sensor assembly (for Bank 2) connector.



A
REPLACE DIFFERENTIAL PRESSURE SENSOR (for Bank 2) (Click here)
B


12. CHECK MIL (NOZZLE VANE POSITION SENSOR (for Bank 1))
  1. Disconnect the C89 nozzle vane position sensor (for Bank 1) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the C89 nozzle vane position sensor (for Bank 1) connector.



A
REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1) (Click here)
B


13. CHECK MIL (NOZZLE VANE POSITION SENSOR (for Bank 2))
  1. Disconnect the z66 nozzle vane position sensor (for Bank 2) connector.

  1. Turn the engine switch on (IG).

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the z66 nozzle vane position sensor (for Bank 2) connector.



A
REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 2) (Click here)
B


14. CHECK HARNESS AND CONNECTOR
  1. Disconnect the throttle position sensor (for Bank 1) connector.

  1. Disconnect the throttle position sensor (for Bank 2) connector.

  1. Disconnect the No. 1 EGR valve connector.

  1. Disconnect the No. 2 EGR valve connector.

  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the differential pressure sensor assembly (for Bank 1) connector.

  1. Disconnect the differential pressure sensor assembly (for Bank 2) connector.

  1. Disconnect the nozzle vane position sensor (for Bank 1) connector.

  1. Disconnect the nozzle vane position sensor (for Bank 2) connector.

  1. A182331E15
    Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C45-91 (VC) - Body ground
    Always
    10 kΩ or higher
    C45-110 (VCVL) - Body ground
    Always
    10 kΩ or higher
    C45-118 (VCM) - Body ground
    Always
    10 kΩ or higher
    C45-120 (VNVC) - Body ground
    Always
    10 kΩ or higher
    C45-66 (VCPM) - Body ground
    Always
    10 kΩ or higher
    A38-55 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A38-56 (VCP2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C46-91 (VC) - Body ground
    Always
    10 kΩ or higher
    C46-110 (VCVL) - Body ground
    Always
    10 kΩ or higher
    C46-118 (VCM) - Body ground
    Always
    10 kΩ or higher
    C46-120 (VNVC) - Body ground
    Always
    10 kΩ or higher
    C46-66 (VCPM) - Body ground
    Always
    10 kΩ or higher
    A52-55 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A52-56 (VCP2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle position sensor (for Bank 1) connector.

  1. Reconnect the throttle position sensor (for Bank 2) connector.

  1. Reconnect the No. 1 EGR valve connector.

  1. Reconnect the No. 2 EGR valve connector.

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the differential pressure sensor assembly (for Bank 1) connector.

  1. Reconnect the differential pressure sensor assembly (for Bank 2) connector.

  1. Reconnect the nozzle vane position sensor (for Bank 1) connector.

  1. Reconnect the nozzle vane position sensor (for Bank 2) connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← ECM Power Source Circuit (from Jan 2012)Cranking Holding Function Circuit (from Jan 2012) →