2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0504 Brake Switch "A" / "B" Correlation

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:
The normal signal conditions are as shown in the table below.
Signal (ECM Terminal)
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

  1. [OFF] denotes ground potential.
  2. [ON] denotes battery potential (+B).
  3. On the intelligent tester, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the characteristics of ST1 indication are the opposite of the Stop Light Switch indication.
DTC Code
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) The ignition switch is ON.
(b) The brake pedal is released.
(c) The STP signal is OFF when the ST1- signal is OFF.
  1. Short in stop light switch signal circuit
  2. STOP fuse
  3. IGN fuse
  4. Stop light switch
  5. ECM

WIRING DIAGRAM

A160611E02

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. STP signal conditions can be checked using the intelligent tester.
    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the tester on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.
    5. Check the STP signal when the brake pedal is depressed and released.

Brake Pedal Operation
Specified Condition
Depressed
STP signal ON
Released
STP signal OFF

1. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
B158579E20
  1. Disconnect the stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A30-2 - Body ground
    Always
    11 to 14 V
    A30-3 - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 4
OK


2. INSPECT STOP LIGHT SWITCH ASSEMBLY
C171632E01
  1. Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    Switch pin pushed
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3. CHECK ECM (STP AND ST1 - VOLTAGE)
A112585E34
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A38-35 (ST1-) - Body ground
    Brake pedal released
    11 to 14 V
    Brake pedal depressed
    0 to 3 V
    A38-36 (STP) - Body ground
    Brake pedal released
    0 to 3 V
    Brake pedal depressed
    11 to 14 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A52-35 (ST1-) - Body ground
    Brake pedal released
    11 to 14 V
    Brake pedal depressed
    0 to 3 V
    A52-36 (STP) - Body ground
    Brake pedal released
    0 to 3 V
    Brake pedal depressed
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

4. INSPECT FUSE (STOP, IGN)
A162154E02
  1. Remove the STOP and IGN fuses from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    STOP fuse
    Always
    Below 1 Ω
    IGN fuse



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR


← P0500 Vehicle Speed Sensor "A" (from Jan 2012)P0504 Brake Switch "A" / "B" Correlation (from Jan 2012) →