P0504 Brake Switch "A" / "B" Correlation
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.- HINT:
- The normal conditions are as shown in the table below.
Signals
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Release and depress brake pedal with ignition switch ON |
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch is ON. (b) Brake pedal is released. (c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on. |
|
| DTC No. |
Data List |
| P0504 |
Stop Light Switch |
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- Stop light switch conditions can be checked using the intelligent tester.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the tester on.
- Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch.
- Check Stop Light Switch when the brake pedal is depressed and released.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| Brake Pedal Operation |
Specified Condition |
| Depressed |
ON |
| Released |
OFF |
| 1. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE) |
Disconnect the stop light switch connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
A30-2 - Body ground
Always
11 to 14 V
A30-4 - Body ground
Ignition switch ON
11 to 14 V
|
|
||||
| OK | |
| 2. INSPECT STOP LIGHT SWITCH ASSEMBLY |
![]() ![]() |
Remove the stop light switch.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Switch pin not pushed
Below 1 Ω
Switch pin pushed
10 kΩ or higher
3 - 4
Switch pin not pushed
10 kΩ or higher
Switch pin pushed
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK ECM (STP AND ST1- VOLTAGE) |
![]() ![]() |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for LHD Tester Connection
Brake Pedal Condition
Specified Condition
A38-35 (ST1-) - Body ground
Released
11 to 14 V
Depressed
0 to 3 V
A38-36 (STP) - Body ground
Released
0 to 3 V
Depressed
11 to 14 V
for RHD Tester Connection
Brake Pedal Condition
Specified Condition
A52-35 (ST1-) - Body ground
Released
11 to 14 V
Depressed
0 to 3 V
A52-36 (STP) - Body ground
Released
0 to 3 V
Depressed
11 to 14 V
|
|
||||
|
|
||||
| 4. INSPECT FUSE (STOP, IGN) |
![]() ![]() |
Remove the STOP and IGN fuses from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
STOP fuse
Always
Below 1 Ω
IGN fuse
|
|
||||
|
|
||||
| 5. REPLACE STOP LIGHT SWITCH ASSEMBLY |
Replace the stop light switch assembly (Click here).
|
|
||||
| 6. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 7. REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
||||
| 8. CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE |
| NEXT | |
| 9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the tester on.
Brake pedal released and depressed.
Enter the following menus: Powertrain / Engine / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||



