2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0560 System Voltage

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.
P0560 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds
The voltage at terminal BATT drops excessively for 3 seconds and part of the stored values in the ECU are initialized (1 trip detection logic).
  1. Open in back up power source circuit (to BATT terminal)
  2. Battery
  3. Battery terminals
  4. EFI MAIN fuse
  5. ECM
Related Data List 
DTC No.
Data List
P0560
Battery Voltage

HINT:
If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly erased.


WIRING DIAGRAM

A263485E01

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
  2. When the ignition switch is ON, even though +B voltage is present, when the voltage at terminal BATT (power supply for maintaining memorized values in the ECM) drops excessively, a DTC is stored.


1. INSPECT FUSE (EFI MAIN)
A162283E03
  1. Remove the EFI MAIN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI MAIN Fuse
    Always
    Below 1 Ω



NG
Go to step 7
OK


2. CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - ECM, BATTERY)
A162155E03
  1. Check the harness and the connector between the EFI MAIN fuse and ECM.

    1. Remove the EFI MAIN fuse from the engine room relay block.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open):
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse (2) - A38-20 (BATT)
      Always
      Below 1 Ω
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse (2) - A52-20 (BATT)
      Always
      Below 1 Ω


      Standard Resistance (Check for Short):
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse (2) or A38-20 (BATT) - Body ground
      Always
      10 kΩ or higher
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse (2) or A52-20 (BATT) - Body ground
      Always
      10 kΩ or higher

  1. Check the harness and the connector between the EFI MAIN fuse and battery.

    1. Remove the EFI MAIN fuse from the engine room relay block.

    2. Disconnect the cable from the positive (+) battery terminal.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open):
      Tester Connection
      Condition
      Specified Condition
      Battery positive terminal - EFI MAIN fuse (1)
      Always
      Below 1 Ω

      Standard Resistance (Check for Short):
      Tester Connection
      Condition
      Specified Condition
      Battery positive terminal or EFI MAIN fuse (1) - Body ground
      Always
      10 kΩ or higher



NG
Go to step 8
OK


3. INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted.



NG
Go to step 9
OK


4. CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
Go to step 10
OK


5. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON for 3 seconds.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0560 is output
    A
    No DTC is output
    B



B
END
A


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11
7. CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE


NEXT
Go to step 11
8. REPAIR OR REPLACE HARNESS OR CONNECTOR


NEXT
Go to step 11
9. REPLACE BATTERY


NEXT
Go to step 11
10. REPAIR OR REPLACE BATTERY TERMINAL

NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON for 3 seconds.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0504 Brake Switch "A" / "B" Correlation (from Jan 2012)P0560 System Voltage (from Jan 2012) →