2011-2013 Land Cruiser · Service Manual Vehicle Interior

B2273 Ignition 2 Monitor Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is stored when a malfunction occurs in the IG2D output circuit, which is between the integration relay (IG2 relay) actuation circuit inside the main body ECU and the integration relay (IG2 relay).
DTC Code
Detection Condition
Trouble Area
B2273
The integration relay (IG2 relay) actuation circuit inside the main body ECU or other related circuit is malfunctioning.
  1. Main body ECU
  2. IG2 MAIN fuse
  3. Integration relay (IG2 relay)
  4. Harness or connector

WIRING DIAGRAM

A175470E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (IG2 RELAY MONITOR (INSIDE))
  1. Use the Data List to check if the integration relay (IG2 relay) is functioning properly.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG2 Relay Monitor (Inside)
    Integration relay (IG2 relay) inner relay monitor/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -

    OK:
    When the engine switch is turned on (IG), ON is displayed on the tester.



NG
Go to step 3
OK


2. CHECK WHETHER DTC OUTPUT RECURS
  1. Clear the DTCs (Click here).

  1. Turn the engine switch on (IG), wait at least 10 seconds, and check whether DTC B2273 is output.

    Result 
    Result
    Proceed to
    No DTC output
    A
    DTC B2273 output
    B



B
REPLACE MAIN BODY ECU
A

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT FUSE (IG2 MAIN)
  1. Remove the IG2 MAIN fuse from the integration relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IG2 MAIN fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE (IG2 MAIN)
OK


4. INSPECT INTEGRATION NO.1 RELAY (IG2 RELAY)
A175471E01
  1. Install the IG2 MAIN fuse to the integration relay.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1B-8 - 1C-1
    Battery voltage applied to terminals 1B-6 and 1B-7
    Below 1 Ω
    1B-8 - 1C-1
    Battery voltage not applied to terminals 1B-6 and 1B-7
    10 kΩ or higher



NG
REPLACE INTEGRATION NO.1 RELAY (IG2 RELAY)
OK


5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY (IG2 RELAY) AND BODY GROUND)
A175472E02
  1. Disconnect the E2 main body ECU connector.

  1. Disconnect the 1B integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-11 (IG2D) - 1B-6
    Always
    Below 1 Ω
    1B-7 - Body ground
    Always
    Below 1 Ω
    E2-11 (IG2D) or 1B-6 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← B2272 Ignition 1 Monitor Malfunction (from Jan 2012)B2273 Ignition 2 Monitor Malfunction (from Jan 2012) →