2011-2013 Land Cruiser · Service Manual Brake

C1432 Steering Angle Sensor Power Source Voltage Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2012

DESCRIPTION

Steering sensor signals are sent to the skid control ECU (master cylinder solenoid) via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering angle sensor zero point malfunction diagnostic function.
DTC Code
DTC Detection Condition
Trouble Area
C1432
A steering sensor power supply malfunction signal is received from the steering sensor.
  1. ECU-B1 fuse
  2. ECU-IG No. 2 fuse
  3. Steering sensor power supply
  4. Steering sensor
  5. Steering control ECU (w/ VGRS)

WIRING DIAGRAM

C257149E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the steering sensor, confirm that the replacement part is of the correct specification.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When the speed sensor or the yaw rate sensor assembly has trouble, DTCs for the steering sensor may be stored even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate sensor assembly are output together with DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate sensor assembly first, and then inspect and repair the steering sensor.


1. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output (for LHD)
    B
    CAN DTC is output (for LHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2. CHECK HARNESS AND CONNECTOR (IG/ESS TERMINAL)
C122523E12
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness in the locking part and connecting part of the connectors.

  1. Disconnect the steering sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E11-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E11-2 (ESS) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Steering Sensor)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (BAT TERMINAL)
C122523E13
  1. Turn the ignition switch off.

  1. Disconnect the steering sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E11-3 (BAT) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Sensor)
    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ VGRS)
    B
    NG (w/o VGRS)
    C



B
Go to step 4

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE STEERING SENSOR (Click here)

4. CHECK HARNESS AND CONNECTOR (+BI TERMINAL)
C139753E04
  1. Turn the ignition switch off.

  1. Disconnect the steering control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E77-10 (+BI) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (STEERING SENSOR - STEERING CONTROL ECU)
  1. Turn the ignition switch off.

  1. Disconnect the E11 steering sensor connector.

  1. Disconnect the E79 steering control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E11-3 (BAT) - E79-1 (+BO)
    Always
    Below 1 Ω
    E11-3 (BAT) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE STEERING CONTROL ECU (Click here)

C
REPLACE STEERING CONTROL ECU (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR


← C1425 Open in Stop Light Switch Circuit (from Jan 2012)C1433 Steering Angle Sensor Internal Circuit (from Jan 2012) →